© Copyright 2015 Star Water Systems. All rights reserved.
1
1. To reduce the risk of electrical shock, a properly grounded
receptacle of grounding type must be installed and protected
by a ground fault circuit interrupter (GFCI) and in accordance
with national electrical code and local codes.
2. Make certain that the receptacle is within the reach of the
pump’s power supply cord. DO NOT USE AN EXTENSION
CORD. Extension cords that are too long or too light do
not deliver sufcient voltage to the pump motor. But more
important, they could present a safety hazard if the insulation
were to become damaged or the connection end were to fall
into the sump.
3. Testing for Ground. As a safety measure, each electrical
outlet should be checked for ground using an Underwriters
Laboratory Listed circuit analyzer which will indicate if the
power, neutral and ground wires are correctly connected to
your outlet. If they are not, call a qualied electrician.
4. For electrical safety, it is recommended that a GFCI be
installed.
5. FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP
FROM ITS POWER SOURCE BEFORE HANDLING. Single
phase pumps are supplied with a 3-prong grounded plug to
help protect you against the possibility of electrical shock.
DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE
THE GROUND PIN. To reduce the risk of electrical shock,
a properly grounded receptacle of grounding type must be
installed and protected by a ground fault circuit interrupter
(GFCI) in accordance with national electrical code and local
codes.
6. Installation and checking of electrical circuits and hardware
should only be performed by a qualied licensed electrician.
7. Risk of electric shock - These pumps have not been
investigated for use in swimming pool and marine areas.
8. According to the state of California (Prop 65), this product
contains chemicals known to the state of California to cause
cancer and birth defects or other reproductive harm.
NOTICE TO INSTALLER: Instructions must remain with installation.
FW0131
0415
Supersedes
0202
Model S1108
CRAWL SPACE
®
PUMPING SYSTEM
PREINSTALLATION CHECKLIST
Through research and development, design, testing and manufacturing, we have been able to bring products to the market that
solve problems that plague consumers, industry, and the environment. This commitment to our customers has enabled them to enjoy
returns of our joint efforts.
1. Inspect your unit. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before using.
DO NOT remove the test plugs in the cover nor the motor housing.
2. Carefully read the literature provided to familiarize yourself with specic details regarding installation and use. These materials
should be retained for future reference.
1. Check to be sure your power source is adequate for handling
the voltage requirements of the motor, as indicated on the
pump or basin plate.
2. Make sure the pump electrical supply circuit is equipped
with fuses or circuit breakers of proper capacity. A separate
branch circuit is recommended, sized according to the
National Electrical Code for the current shown on the pump
name plate.
3. Pump should be checked frequently for debris and/or build
up which may interfere with the oat “on” or “off” position.
Repair and service should be performed by an Authorized
Service Station only.
4. A CHECK VALVE MAY BE REQUIRED TO REDUCE
UNNECESSARY CYCLING OF PUMP.
5. Dewatering pumps are not designed or intended for handling
raw sewage.
6. Maximum operating temperature for Crawl Space Drain
Pumps must not exceed 130°F (54°C).
SEE BELOW FOR LIST OF WARNINGS
SEE BELOW FOR LIST OF CAUTIONS
REFER TO WARRANTY PAGE 2.
NOTE: Pumps with the “UL” mark and pumps with the “US”
mark are tested to UL Standard UL778. CSA Certied
pumps are certied to CSA Standard C22.2 No. 108.
Product information presented
here reects conditionso at time of
publication. Consult factory regarding
discrepancies or inconsistencies.
STAR
®
95 N. Oak St. • Kendallville, IN 46755
To Next Page
Need help?
General
