Technics Quartz ST-G7 User Manual

e How to preset radio broadcast frequencies
Important!
This antenna must be installed
to receive AM broadcasts.
AM loop antenna
e Manual memory presetting
Stations can be freely preset to any desired channel.
This unit is used to preset as many as 16 radio broadcast
frequencies: FM/AM random presetting. After broadcast fre-
@ Before memory presetting
Each button is used to preset two stations.
quencies have been preset as described below, any desired
station can be quickly and easily selected by simply touching
one button.
Presetting front
channels (CH 1~8)
@ Memory presetting at
There
are
two
types
of
memory
presetting:
automatic
and
¢
Press
manual. Select whichever is preferred. momentarily.
e Automatic memory presetting
Beginning at the frequency indicated by the digital display, the FM broadcasting stations and AM broadcasting
stations will be automatically preset to “channels” 1 through 16 for FM and 9 through 16 for AM, respectively.
Note that in mountainous or remote areas, broadcasting stations which have weak broadcasting signals cannot be
Q Press the appropriate tuning button to tune to the desired broadcast:
Presetting back
channels (CH 9~16)
Press slightly
e Auto tuning
Press the button. When the frequency
indication begins to change, release the
button (a broadcasting station will be
selected automatically). Repeat this
e Manuai tuning wt
Press the button momentarily and tune to u(
the desired station (the frequency will
change each time the button is pressed).
operation until the desired station is found.
Adjustment to FM broadcast signal strength is possible for
automatic tuning.
Press and hold the button. (Will change to dB indication.)
Release the buiton when the desired scan level indication (30, 40 or
50 dB) is displayed. (When the scan level is set, it will return to frequency
automatically preset into the memory.
a Power: “on” ( B--m= )
Adjustment to FM broadcast signal strength is possible.
Press and hold the button. (Will change to dB indication.) Release the
button when the desired scan level indication (30, 40 or 50 dB) is
displayed. (When the scan level is set, it will return to frequency display.)
A broadcast signal stronger than the set level is memorized.
@ Press the “FM” or “AM” button:
To change the AM frequency by 10 kHz:
Press the “AM” button slightly longer and
release the button when the “AL 10”
is displayed.
wo PM/AM random ch preset tuning : a
display.)
Power: “on” ( Bm )
@ Press the “FM” or “AM” button.
To change the AM frequency by 10 kHz:
Press the “AM” button slightly longer and
release the button when the “AL 10”
is displayed.
Memory indicator
| Casein: Syrtnemiver FM/AM Stereo Tuner 8-4
ert cK/F MM mang off
ni me ci
Cy
-_ FM/AM fandom i6ch praset tuning ~
digest Ate oe 16 aid %
=
or)
Confirm the names (call signs, etc.) of the broadcasting
stations which are preset to each channel, and enter them on
the station memory file sheet.
To check the front channels (CH 1~8):
Press Frequency stored in the
momentarily. memory and channel number
ley Press. When the frequency
indication begins to
change, release.
While the memory indicator is illuminated,
press the button of the desired channel.
Press momentarily, and then
release.
(The memory indicator will
beg are displayed.
A
To check the back channels (CH 9~16):
Frequency
stored
in
the
order.
Press slightly
longer. memory and channel number
are displayed.
(The frequency will change upward,
and the automatic presetting will begin
with the broadcasting station of the
lowest frequency and will continue in
Note that the channel display
illuminates each time a broadcast
station is preset in the memory,
thus indicating which “channel” has
been preset.)
7
t
D2
on]
My
(4) © To preset FM broadcasting stations: Set to 87.50 MHz.
® Topreset AM broadcasting stations: Set to 522 kHz (or 530 kHz).
@ Press the button and
hold slightly
(frequency will change
continuously).
@ Release it at 87.50 MHz for FM or
522 kHz (or 530 kHz) for AM, and
then press the button again
momentarily
(frequency change will stop).
@ Press the button
momentarily (frequency will change
each time the button is pressed), and
tune to one of the above frequencies.
© To preset channels 1 through 8:
x Press the button momentarily, and then
Ci release. (Preset channel number is
displayed on the channel display.)
© To preset channels 9 through 16:
- ae Press the button slightly longer, and then
release. (Preset channel number is
displayed on the channel display.)
When the button is pressed, the memory
indicator illumination will stop, and the
presetting is complete.
Note:
1. If the memory indication illumination
stops before you press the button, once
again repeat step (5) and then step (6).
2. If a new broadcasting station is preset
into a channel, the broadcasting station
which was previously entered in that
channel will be automatically erased.
illuminate for approximately
4 seconds.)
4
A
Note:
If the button is pressed continuously,
the frequency will begin to change,
and the memory will be preset
automatically.
To stop the automatic memory
presetting, once again press either
the “up” button or the “down” button.
7) Enter the name (call sign, etc.) of the preset broad-
casting station on the station memory file sheet.
This completes the procedures for presetting radio broad-
cast frequencies. The other preset-tuning butfons can be
preset in the same way by following steps (2) through (7).

Technics Quartz ST-G7 Specifications

General

Brand	Technics
Model	Quartz ST-G7
Category	Tuner
Language	English