Technics SL-D2 Service Manual

m@ REPLACEMENT PARTS LIST
Notes: 1.
Please use this part number for parts orders.
Part numbers are indicated on most mechanical parts.
2. A indicates that only parts specified by the manufacture be used safety.
3. SL-D2 (XA)—> [XA] , SL-D2 (XAL)-—> [XAL] , SL-D2 (XGE)—> [XGE] , SL-D2 (E) > [E] , SL-D2 (XG)—> [XG]
SL-D2 (XGF)— > [XGF] , SL-D2 (XGB)— > [XGB] , SL-D2K (XAL)—=> [KXAL], SL-D2K (E) ~ [KE],
SL-D2K (XG)—> [KXG] ,SL-D2K (XA)—> [KXA]
INTEGRATED CIRCUIT
AN630U
integrated Circuit
TRANSISTORS
25C 1846-R
2SD637
25B641
Transistor
Transistor
Transistor
DIODES
Rectifier
Rectifier
Diode
Diode
Light Emitting Diode
SVDSIRBA40
SVDM1152
20A90
MA161
SVDGD4205ALC
Part No.
Part Name & Description
TRANSFORMER
SLT5352A Sis Transformer
FUSE
125mA, Fuse
400mA, Fuse
XBA2C012TRO
XBA2CO04T RO
SWITCHES
SFDSAH74403 Switch, Power
EVAH27SBCAAY j|Switch, Speed Selector
SFDSHXW13312 = {|Switch, Power Selector
VARIABLE RESISTORS
EVLS6AA00B54 {50k (B), Speed Control (33 r.p.m. &
45 r.p.m.)
20kQ. (B), Pitch Control EVJ61AT12B24
g@ ADJUSTMENT PROCEDURE
Adjustment of Speed (See Fig. 12)
If the number of revolutions cannot be correctly adjusted
by replacing IC or other parts and turning the fine speed
adjusting knob (VR3), make the re-adjustment according to
the following procedure.
1, Set the fine speed adjusting knob to the central position.
2. In 33-1/3 r.p.m. mode, turn VR1 (33) so that the speed
is adjusted to the specified point by using a stroboscope.
3. Next, in 45 r.p.m. mode, turn VR2 (45) so that the
speed is adjusted to the specified point by using a strobo-
scope.
4. After the adjustment, shift the speed change switch and
make sure that the speeds in 33-1/3 r.p.m. and 45 r.p.m.
modes are as specified.
Note:
For the above adjustments, follow the disassembly pro-
cedure. Remove the bottom plate and put the set ona
table for repair work and gain access to it from
underneath.
RESISTORS
ERXTANJ3R9
ERD25FJ822
ERD25FJ472
ERD25FJ330
ERX1ANJ3R9
ERO25CKF6202
ERD25TJ393
ERD25TJ104
ERD25TJ563
ERD25FJ102
ERO25CKF3902
ERD25FJ103
ERD25FJ331
ERD25TJ223
Metallic,
Carbon,
Carbon,
Carbon,
Metallic,
Metal Fitm,
Carbon,
Carbon,
Carbon,
Carbon,
Metal Film,
Carbon,
Carbon,
Carbon,
CAPACITORS
ECEB1HS471
ECEA25Z4R7
ECEA50ZR22
ECQM1H104KS
ECEA50ZR33
ECEASON1
ECEASON1
ECQF2334KZ
ECQM1H154KZ
ECQM1H104KS
ECEA25M10R
ECEASOM2R2R
ECEASOMR33R
ECEA1V$330
ECQM1H472KZ
ECQM1H473KZ
ECEAS0Z1
ECEA502Z1
ECEA1AS221
ECQM1H333KZ
Electrolytic,
Electrolytic,
Electrolytic,
Polyester,
Electrolytic,
Non-polar Electrolytic, 1pF, 50V
Non-polar Electrolytic, uF, 50V
Polypropyiene, 0.33 uF ,
Polyester,
Polyester,
Electrolytic,
Electrolytic,
Flectrolytic,
Electrolytic,
Polyester,
Polyester,
Electrolytic,
Electrolytic,
Electrolytic,
Polyester,
3.90, IW,
8.2kN,
4.7kQ,
330,
3.9kQ), Ww
62k,
30k,
100kQ),
56kN),
1k,
39kN.,
10kQ,
330M.
22kQ),
A70uF, 50V
47yF, 25V
0.22uF, 50V
O.1uF, 50V,
0.33uF, 50V
50V,
5OV,
0.15 uF,
O.1pF,
10uF , 25V
2.2uF, 50V
O.33uF, 50V
33 uF , 25V
0.0047H#F, 50V,
0.00474F, 50V,
50V
50V
/ 6.3V
0,0033uF, 50V,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
1/4W,
200V,
HHH HH HH HOH OE
HoH He
+10%
+10%
+10%
It is also possible to adjust the set only with its turntable
removed,
Remove the turntable as tllustrated below, then a hole will
be revealed from which a screwdriver can be inserted to
turn VR1 and VR2.

Technics SL-D2 Specifications

General

Brand	Technics
Model	SL-D2
Category	Turntable
Language	English