H9 ASD
H9 ASD Simple Start Guide
The H9
ASD
Simple Start Guide provides instructions on installation and operating procedures only.
For additional information regarding your new H9 ASD, consult the
H9 ASD Installation and Operation Manual
.
DO NOT
attempt to install or operate the H9 ASD until you have read and understood all of the user directions
contained in this guide, and the p rod uc t saf ety inform at ion and prod uc t labels c onta ined in th e
H9 ASD Installation
and Operation Manual
. Equipment wa rning lab e ls pr ovide use ful inform at ion and ind ica te an imm in ent ly hazardous
situation that may result in serious injury, severe property and equipment damage, or loss of life if safe procedures are
not followed.
Installation and operat ion sh all be p erf orm ed by qualif ied p erson ne l only.
Frequently Asked Questions
General
Q
:
I did not receive an Instal l ation an d Operation M anual wi th my AS D. How can I get one?
A
:
The
H
9 ASD Quick Start Gui de
and
the
H9
ASD
I nstal l ation and Operation Manual
can b e downloaded from our website. To request a hard-copy of either document
contact the Toshiba Customer Support Center or your local Toshiba distributor.
Q
:
Does Toshiba of fer training courses?
A
:
Yes. Training courses are offered at TIC
headquarters in Houston, Texas. There are two types of training — maintenance and repair (nominal fee), and applications (free). Our instructors have years
of hands-on experience in their respective fields and are continually being trained on new products. Students will gain valuable experience on the equipment and troubleshoot real faults that
may b
e incurred during normal ASD setup, operation, and maintenance.
For a listing of upcomin g training courses or to register, visit our website an d click o n the trainin g tab.
Q
:
Where
can I find
additional informatio n about Toshiba International Corporation (TIC) an d TIC products?
A
:
Additional information can be foun d on our website
.
You may also contact
TIC for additional information by writing to 13131 West Little York Rd., Houston, Texas, 77041,
via
telephone at (713) 466-0277, or via fax at (713) 937-9349.
Application Specific
Q
:
Who is considered qualified personnel?
A
:
A qualified person is one who has the skills and knowledge about the construction, installation, operation, and maintenance of the equipment and has received safety training on the hazards
involved. Qu alified person nel are able to recognize and proper ly addre ss hazards a ssociated wit h the application of motor-d riven equipment, and are trained to safely energize, de-energize
and
ground said equipment, to safely lockout/tagout circuits and equipment, and clear faults in accordance with established safety pr actices.
Q
:
What d o I do if my mo tor is rotati ng in the wro ng d irection?
A
:
Qualified personnel should reverse any two of the three ASD
output power leads (U/T1, V/T2, or W/T3) connected to the motor.
Q
:
For safety and application-specific reasons I need to remotely mount the ASD. How do I accomplish this?
A
:
Select a mounting location that is easily accessible by the user and mark the location of the screw holes. After drilling the screw holes, attach and secure the Electronic Operator Interface (EOI) to
the front side of the mounting location. Connect the extension cable. For information on required hardware or for instructions on remote mounting using a Remote Mounting Kit, consult the
H9
ASD Installation and Operation Manual
.
If further assistance is required,
contact the Toshiba Customer Support Center.
Q
:
I followed all of the instructions but my motor will not run. Wha t now ?
A
: Ensure that the input power to the ASD is connected and that the voltage at R/L1, S/L2, and T/L3 are as specified for your unit.
Ensure that the terminals of the terminal board are configured
correctly for your application.
Perform a Rese t (to factor y def au lt settin gs).
Ensure that the Local/Remote key is as required for your application and that you have provided a run command. If
further assistance is required,
contact the Toshiba Customer Support Center.
Q
:
During system operation I receive error messages that I do not understand. W here can I find information about trips/faults/alarms and troubleshooting?
A
:
A complete list of LED
and
LCD screen displays, trip/fault/alarm descriptions and a list of possible causes of all trips/faults/alarms can be found in the
H9 ASD Installation and Op eration Man ual
.
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
To Next Page
Need help?
General
