If you are using an external antenna to connect, please refer to Appendix 1.
Typical Network
Conguring the Device
3
1
Open your web browser, type in http://192.168.0.254 in the address eld
and press Enter．
2
A dialog box will prompt you for the User name and Password. Enter the
default values (both are admin) and click OK.
1. If the dialog box does not pop up, please refer to T3 in the Appendix 2:
Troubleshooting. Also, T2 will give you some help if you forget the
password.
2. If the device has been restored, the Welcome page will appear, please
read the TERMS OF USE carefully. Then select I agree to these terms of
use and click Login to continue.
3
The web management page will display after your successful login. Click Quick
Setup in the main menu．
4
Then the page below will appear. Click Next．
5
Select the Operation Mode Type according to your needs. Click Next.
a) If you want to set up a point-to-point connection with TL-WA7210N, please
skip to Conguration for Point-to-Point Connection. In this part, you will
learn about the conguration for Access Point and Client mode.
b) If you want to set the CPE to the Bridge with AP mode, please skip to
Conguration for Bridge with AP.
(To be continued...)
Conguring the Computer
2
Assign a static IP address 192.168.0.100 for your computer rst before logging in
the management page. Here we take the procedures in Windows 7 for example.
1
Go to Start > Settings > Control
Panel, and then you will see the
following page. Click View
network status and tasks.
2
Click Change adapter settings.
3
Right-click Local Area Connec-
tion, then click Properties.
4
Double-click Internet Protocol
Version 4 (TCP/IPv4).
5
Select Use the following IP
address, enter 192.168.0.100 into
the IP address eld and
255.255.255.0 into the Subnet
mask eld．
For conguration for other modes of TL-WA7210N, please refer to the
User Guide in the resouce CD.
Point-to-Multipoint Application
AP
Client 2
Client 3
Client 1
Point-to-Point Application
Client
AP
Connecting the Device
1
Please use only wired network connection to congure the AP.
1
2
3
Locate a suitable mounting site for your CPE. To achieve the best performance
of the devices, please select an elevated location where trees, buildings and
large steel structures will not obstruct the antenna signals and which oers
maximum line-of-sight propagation for the devices.
Adjust the direction of your CPE for a best signal. Place the straps through the
slots on the back of the CPE and then around the pole. Tighten the straps.
TL-WA7210N
Power Adapter
PoE
Computer
Connect one end of an Ethernet cable to the PoE port of the provided PoE and
the other end of the Ethernet cable to the LAN port of the CPE. Then, connect
the LAN port of the PoE to a PC using another Ethernet cable. Finally, plug the
provided power adapter into the DC jack on the PoE, and the other end to a
standard electrical wall socket.
4
The connection will be similar to the gure below after the above steps are
nished.
5
Turn on all your network devices and then check to see if the LEDs on the AP
display normally as the diagram below describes.
If the LEDs display abnormally, please check to see if all the cable
connectors (power adapter and Ethernet cable) are well connected to
your devices.
Solid light
Solid light
Solid light or ashing
OUTDOOR
INDOOR
CPE
Power Cable
Main Electrical Supply
PoE Injector
To Switch or PC
CAT5 FTP Cable Ethernet + DC Power
6
Click OK to save the congura-
tions for your computer.
6
If you use two CPEs to build the network, please make sure that the two CPEs
are placed face to face. Please refer to the Antenna Alignment to get the
optimum signal.
Mounting Kits
Please recongure your computer after successfully conguring the CPE.
Select Obtain an IP address automatically and Obtain DNS server
address automatically in step 5, then click OK.
To Next Page
Need help?
General
Weight and Dimensions
