STEP2 Point the remote at the
component and press and
hold the [DEVICE] key for 5
seconds until the Device LED
blinks off and turns back on.
Continue holding the [DEVICE]
key and press the numberkeys,
one at a time, starting with 1,
then2, 3...0. Stop pressing
the number keys when the
device turns off.
STEP3 Release the [DEVICE] key to
save the code. The Device
LED will blink twice to
confirm the code is stored.
Repeat the steps above for all
components(CBL, TV).
B.
B.
Manual Programming
Manual Programming
The remote control can be programmed
by entering a three-digit code number
that corresponds to particular brands
and models of equipment. The three-
digit code numbers are listed in the
code tables sections of this instruction
manual.
STEP1 Turn on the equipment that
you want the remote con-
trol to operate (Cable Box or
TV).
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The corresponding device
LED will turn on indicating
that it is ready to be pro-
grammed. The LED will remain
on for 30 seconds. The next
step must be entered while
the LED is on.
STEP3 Point the remote control
toward the equipment and
enter the three-digit code
number assigned to your
brand from the code tables.
If there are more than one
three-digit number listed for
your brand, try one code
number at a time until your
equipment turns off.
*Note: You can verify that you have
selected the correct code by
pressing the [POWER] button.
The equipment should turn
back on. Then try all of the
functions on the remote
control (i.e. volume, mute,
etc.) to ensure you have the
correct code. If any of the
functions do not operate as
they should, repeat the
instructions from STEP 3
above using the next three
digit code number from the
brand list.
STEP4 Store the three-digit code
by pressing the same
[DEVICE] button once again.
The device LED will blink
twice to confirm that the
code has been stored.
C. Auto Search Method
C. Auto Search Method
If none of the three digit code numbers
assigned to your brand of equipment
works, or the code table does not list
your brand, you can use the Auto
Search Method to find the correct
three-digit code number for your
equipment by following steps:
STEP1 Turn on the equipment that
you want the remote control
to operate (Cable Box or TV).
STEP1 Press the [CBL] button.
STEP2 Press the [All OFF] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The [CBL] button will turn
on for 30 seconds.
STEP3 Press the first [Device] button
you want to store in the
[ALL OFF] button and then
the [POWER] button. Repeat
this for other Device until
you have stored all the
desired power commands
into the [ALL OFF] button.
STEP4 Press the [CH5] button to
save the power commands
you stored. The [CBL]
button will blink twice to
confirm the Device have
been saved.
E.
E.
Programming Volume
Programming Volume
Control
Control
By default, the VOL+, VOL- and MUTE
keys operate through your TV. If you
would like those keys to operate
those functions on a different device,
follow these steps.
STEP1 Press the [OK/SEL] button and
[CBL] button simultaneously
for 3 seconds. The device LED
will turn on for 30 seconds.
The next step must be
performed while the LED is on.
STEP2 Press the [VOL+] button.
The device LED will blink.
STEP3 Press the [DEVICE] button
corresponding to the device
that you would like the
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The device LED will turn on
indicating that it is ready to
be programmed. The LED
will remain on for 30 seconds.
The next step must be enter-
ed while the LED is on.
STEP3 Press the [CH5] or [CH6]
button one at a time or keep
it pressed. The remote will
emit a series of Power
ON/OFF code signals. Release
the [CH5] or [CH6] button
as soon as the equipment
turns off.
*Note: You can verify that you have
selected the correct code by
pressing the [POWER]
button. The equipment
should turn back on. Then
try all of the functions on
the remote control (i.e.
volume, mute, etc.) to ensure
you have the correct code. If
any of the functions do not
operate as they should,
repeat the instructions from
STEP 3 above to continue
the Auto Search Method.
STEP4 Press the same [DEVICE]
button to store the code.
The Device LED will blink
twice to confirm that the
code has been stored.
D.
D.
Programming the All Off
Programming the All Off
Button
Button
This allows you to program the All Off
button so it can send up to two power
On/Off commands with one button
press.
Button Functions
3
Programming the Remote Control
4
Universal Remote Control, Inc.
www.universalremote.com
OCE-0082E Rev 04 (09/03/12)
UR2-211
Operating Manual
For Easy Clicker
This remote control is designed
to operate most Digital, Analog
Cable boxes, IPTV set top boxes
and TVs.
Introduction
1
Replacing Batteries
2
Before you program or operate the
remote control, you must install
two new AA alkaline batteries.
STEP1 Remove the battery com-
partment cover from the
back of your remote control.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
STEP3
Replace the battery com-
partment cover.
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either
the CBL or TV button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method
A. Quick Set-Up Method
(Refer to the Section 5 Quick Set-up table of codes)
STEP1 Turn on the equipment you want to program. To program your TV, turn on the TV.
To Next Page
Need help?
General
