FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT EXCEED 25 AMPS, 15 VOLT MAXIMUM.
WARNING: Luminaires must be installed in accordance with the National Electrical Code (NEC) and local codes. Failure to do so will void the warranty and may
result in serious injury and/or damage to the luminaire.
SAFETY WARNING: Luminaire can become very hot depending on lamp wattage used. Lens and metal around lamp can become hot enough to blister hands.
Particular care should be taken not to locate luminaires where small children can reach them if high wattage lamps are used.
LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A POOL OR SPA. SECONDARY CABLE IS NOT TO BE BURIED MORE THAN 6”.
WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT TO EXCEED THE TOTAL WATTS OF TRANSFORMER RATING. DO NOT USE EXTENSION CORDS
ON POWER UNITS.
NOTE: Always use UL recognized wire connectors for connections.
LUMINAIRE IS UL LISTED FOR ABOVE GROUND INSTALLATION ONLY.
1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • email@vistapro.com • www.vistapro.com
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
Factory sealed
liquid-tight connector
Housing
Lens
water resistant cable
Conduit sweep
Specialty Lights
Landscape Series
4217
INSTALLATION INSTRUCTIONS - For T3-LED & T3-Halogen
WARNING - TO REDUCE THE RISK OF FIRE, OR INJURY TO PERSONS:
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamps get hot! Contact only switch/plug when turning on.
3. Do not touch hot lens, guard or enclosure.
4. Keep lamp away from material that may burn.
6. Do not operate luminaire fitting with a missing or damaged cover.
IMPORTANT SAFETY INSTRUCTIONS - THE LIGHTED LAMP IS HOT!
SAVE THESE INSTRUCTIONS (Leave with property owner/manager)
See Reverse for Fixtures with
Integrated LED Module
LUMINAIRE MOUNTING:
CAUTION: LUMINAIRE INTENDED FOR USE IN WATER GARDENS AND
PONDS ONLY. NOT FOR USE IN SWIMMING POOL OR SPA APPLICATIONS.
1. To prevent electrical shock, disconnect transformer from electrical supply
before installation or service.
NOTE: DO NOT pull underwater cable. If wire is pulled, it may break liquid
tight seal and void warranty.
NOTE: DO NOT loosen or remove liquid tight connector. This will damage
factory set seal and result in possible leakage.
NOTE: End of underwater cable must be potted to prevent moisture from
entering cable and consequently entering the luminaire. Connection or splicing
of cable must be made above water line and at least 4’ from water edge. This
luminaire comes equipped with 15’ of waterproof cable to facilitate installation
away from water.
NOTE: Each luminaire is factory tested prior to shipment. Traces of water may
be visible as a direct result of factory underwater testing.
2. Strip the two leads from luminaire pigtail. Using the two safety connectors
(provided), connect leads from luminaire to main supply cable leads.
NOTE: Luminaire is supplied with 15’ of 18-2 cable pigtail for secure connection
to main supply cable.
3. Provide power to luminaire and check for proper operation.
REFLECTOR INSTALLATION:
NOTE: Your Vista model 4217 is provided with a spread reector to disperse
light out the sides of the luminaire giving a wash effect if desired. Follow
instructions below for installation.
1. To prevent electrical shock, disconnect transformer from electrical supply
before installation.
2. Loosen the lens screws and remove lens and O-ring.
3. Insert reector into lens, slipping the square holes in reector onto the round
pegs in lens.
4. Clean O-ring and channel and re-install O-ring.
5. Re-install lens and tighten the screws evenly.
LAMP INSTALLATION/REPLACEMENT:
CAUTION: LUMINAIRE IS RATED AT 12 VOLT AC. DO NOT CONNECT
LUMINAIRE TO ANY OTHER VOLTAGE.
CAUTION: Do not exceed maximum wattage marked on luminaire label.
1. To prevent electrical shock, disconnect transformer from electrical supply
before service.
2. Remove fixture from water and allow to dry.
3. Remove screws from lens cover.
4. Remove lens to expose lamp.
5. Replace lamp with correct wattage and type marked on fixture label.
NOTE: DO NOT touch lamp with bare hands. Always use soft cloth to handle
lamp.
6. Re-install lens, gasket, and cover then tighten screws evenly and securely.
To Next Page
Need help?
General