Name: Welch Allyn Connex VSM 6000 series
Brand: Welch Allyn
Rating: 4 (1 reviews)

To Next Page

Welch Allyn Connex

Devices

Directions for use

Software version 2.3X

Default Chapter3
- Table of Contents3
Introduction7
- Connex Vital Signs Monitor 6000 Series7
- Connex Integrated Wall System7
- Indications for Use8
- Contraindications9
Symbols11
Screen Elements15
About Warnings and Cautions21
- General Warnings and Cautions21
Physical Design29
- Vital Signs Monitor 6000 Series29
- Integrated Wall System33
Setup37
- Vital Signs Monitor 6000 Series37
- Supplies and Accessories37
- Insert the Battery37
- Mount the Monitor38
- Attach the Probe Well39
- Attach the Temperature Probe40
- Remove the Temperature Probe and Well40
- Connect the NIBP Hose41
- Disconnect the NIBP Hose41
- Connect the Spo2 Cable or the Spo2/Rra Dual Cable41
- Disconnect the Spo2 Cable or the Spo2/Rra Dual Cable43
- Connect the Patient Movement Cable43
- Disconnect the Patient Movement Sensor and Cable44
- Attach a USB Accessory44
- Detach a USB Accessory45
- Insert a New Roll of Paper45
- Connect AC Power46
- Disconnect AC Power46
- Integrated Wall System47
- Supplies and Accessories47
- Unpack the Wall System47
- Insert the Battery48
- Prepare for Mounting49
- Mounting Location50
- Mount the Wall System50
- Mount the Accessory bin54
- Connect the Blood Pressure (NIBP) Hose56
- Set up the Physical Assessment Instrument Handles and Specula Dispenser56
- Set up the Suretemp® Plus Thermometer57
- Set up the Braun Thermoscan® PRO Thermometer58
- Connect AC Power58
- Attach an Accessory59
Startup61
- Power61
- Power up the Monitor62
- Set the Date and Time63
- Power down the Monitor63
- Reset the Monitor64
- Enter Clinician Information64
Navigation65
- Home Tab65
- Device Status Area65
- Content Area68
- Navigation Area70
Using the Keypad, Keyboard, and Barcode Scanner73
- Open the Numeric Keypad73
- Numeric Keypad73
- Enter a Number74
- Close the Numeric Keypad74
- Open the Keyboard74
- Keyboard74
- Enter a Letter or Number76
- Enter a Symbol or Special Character76
- Enter a Diacritical Mark76
- Close the Keyboard77
- Use a Barcode Scanner77
Host System79
- Overview79
- Monitor Tab80
- Connect to the Central Station81
- Disconnect from the Central Station81
- Continuous Patient Monitoring81
- Activate the Continuous Monitoring Profile82
- Pause Continuous Monitoring (Pause Mode)83
- Resume Continuous Monitoring84
- End Continuous Monitoring84
- Assign a Patient and Location85
Profiles87
- Continuous Monitoring Profile87
- Saving Vital Sign Measurements (Continuous Monitoring Profile)89
- Intervals Monitoring Profile89
- Spot Check Profile90
- Office Profile90
- Profile Feature Comparison91
- Changing Profiles92
Patient Data Management97
- Add a Patient to the Patient List97
- Load Patient Data with a Barcode Scanner98
- Select a Patient98
- Office Profile100
- Manage Patient Records (Continuous Monitoring Profile)101
- Manage Patient Records (Intervals Monitoring, Spot Check, and Office Profiles)103
- Printer104
- Delete a Patient from the List104
Alarms107
- Patient Rest Mode111
- Reset (Pause or Turn Off) Audio Alarms112
- Cancel a Paused Alarm113
- Adjust Vital Sign Alarm Limits113
- Modify Audio Alarm Notification114
- Alarm Messages and Priorities115
- Nurse Call119
Patient Monitoring121
- Standard and Custom Modifiers121
- Custom Scoring122
- Manual Overrides122
- Patient Movement122
- Capnography (CO2)128
- Respiration Rate132
- Ipi134
- Acoustic Respiration Rate (Rra)137
- Nibp140
- Temperature156
- Spo2169
- Sphb175
- Pulse Rate Frame179
- Manual Parameters Frame181
- Physical Assessment Instrument Handles182
Maintenance and Service185
- Perform Periodic Checks185
- Replace the Printer Paper (Connex VSM)186
- Change the Battery (Connex VSM)187
- Remove the Wall System from the Wall (Connex IWS)188
- Change the Battery (Connex IWS)189
- Clean the Monitor190
- Prepare to Clean the Equipment191
- Clean the Accessories192
Advanced Settings193
- General193
- Parameters198
- Data Management205
- Network208
- Service211
Troubleshooting213
- Patient Movement Messages213
- CO2 Messages215
- Rra Messages216
- NIBP Messages217
- Spo2 and Sphb Messages218
- Temperature Messages219
- Weight Scale Messages220
- Physical Assessment Instrument Handles220
- Patient Data Management Messages221
- Communications Module Messages222
- Radio Messages222
- Ethernet Messages222
- USB and USB Flash Drive Messages222
- System Messages223
- Battery Power Manager Messages223
- Configuration Manager Messages224
- Printer Messages224
- Network Messages225
- Problems and Solutions225
Specifications227
- Physical Specifications227
- Environmental Specifications242
- Device Radio242
- Configuration Options242
- Vital Signs Monitor 6000 Series242
- Integrated Wall System243
Standards and Compliance245
- General Compliance and Standards245
- General Radio Compliance246
Guidance and Manufacturer's Declaration251
- EMC Compliance251
- Emissions and Immunity Information251
Appendix253
- Approved Accessories253
- Mounting Options259
- Warranty264

Brand	Welch Allyn
Model	Connex VSM 6000 series
Category	Medical Equipment
Language	English

Welch Allyn Connex VSM 6000 series User Manual

Table of Contents

Other manuals for Welch Allyn Connex VSM 6000 series

Questions and Answers:

Welch Allyn Connex VSM 6000 series Specifications

Related product manuals