Whistler CR90 User Manual

Updating the Database
Follow the steps below to update the Laser-Radar
Detector.
Step 1: Remove the Laser-Radar Detector from the vehicle
and bring it to your PC. Note: You do not need to power
the Laser-Radar Detector to update it.
Step 2: Download the update program and install it on
your PC. Note: Program is not MAC compatible
Step 3: Download and save the .msc file downloaded to
your PC. Create a folder for the unit so you can store future
updates and save this file into the newly created folder.
DO NOT RENAME THE .msc FILE OR TRY TO OPEN IT!
Step 4: Open the update program and plug the USB
cable into the Laser-Radar Detector.
Step 5: Click the “Open File” button on the update
program and locate the saved file from Step 3. Click the
“DB Update” button to install the file.
Step 6: When update is complete, close the update
program, unplug the USB cable and the Laser-Radar
Detector is ready with the new updates.
LASER/RADAR ALERTS
Speed Radar Audio/Visual Alerts
When X, K or Ka is detected, the band ID and signal
strength are displayed. The audio alert is continuous and
has a geiger counter-like pattern. The faster the beep, the
closer or stronger the radar source.
Laser Audio/Visual Alerts
When a laser signal is detected the audio alert is continuous for a
minimum of 3 seconds.
Displays Shows:
OPERATIONOPERATION
Teach/Tutorial Mode
Provides simulated alerts for each type of signal.
 •PressCityandQuietbuttonssimultaneously
 •DisplayShows:
 •PressDarkbuttontoexit.
Alert Priority
When two or more signals are received at the same time,
the alert priority is:
1. Laser 2. Speed Radar 3. Safety Warning System
™
Example: If X band is alerting, then suddenly a laser
signal is detected, the laser warning will override the X
band alert.
Safety Warning System
™
In communities where transmitters are located, the Safety
Warning System
™
providesover60textmessages.When
SWS
™
is detected the audio alert is geiger counter-like.
Safety Warning System Text Message
Example:Poor-Road-Surface.
NOTE: Not all areas have Safety Warning System
™
transmitters.
Intellicord
®
Ready
The optional INTELLICORD
®
power cable allows the user
to remotely control two of the following detector features
(Power On/Off, City Modes, Dim/Dark, Mark Waypoint
andQuiet/AutoQuiet)withapressofabuttonlocatedon
the power cable’s plug. See option mode for selecting the
functions to work with the INTELLICORD
®
.
Reset Features
All user features can be reset to factory settings.
• Unplug the Power Cord from the unit.
• PressandholdthePowerandQuietbuttons.
• Plug the Power Cord into the unit.
• Wait for 2 beeps.
ReleasethePowerandQuietbuttons.
Unit is now reset to the following features and
settings.
OPERATION
Default factory settings are:
1. S1: (For Intellicord
®
)Quietfeature
2. S2: (For Intellicord
®
)PowerONorOFF
3. ADIM:ON(AutoDimON)
4. HIGHWAY Mode
5. Dim/Dark Mode to full illumination of display.
6. AutoQuietModeOFF
7. SWS
™
OFF
8. Vehicle Battery Saver ON
9. Full Power Up sequence
10. Default TONE 3
11. All Bands ON
12. LASER LSID
13. All Laser Windows ON
14. POP
™
OFF
15. Voice
®
ON
16. LED Periscopes to BLNK
17. X/K Filter 1
18. Ka Filter 1
19. TFSR OFF
20. GPS ON
-GPS Related Features-
21. GMT -5
22. DST OFF
23. Heading Voice OFF
24. Clock ON
25. Compass ON
26. Unit of Measure ENG
27. Over Speed CLEARED
28. High Speed CLEARED
29. Odometer CLEARED
30. ET CLEARED
31.AutoQuietSpeed0
32. Auto Filter Speed 0
33. Alarm Radius: 400
34. Delete Radius: 400
OPERATION OPERATION
LASER/RADAR ALERTS TROUBLESHOOTING
Whistler has two features that will assist the driving enthusiast to
further identify threats from laser and Ka band radar guns.
Ka RSID (Ka Radar Signal IDentifier)
Identify the difference between the likelihood of a Ka threat vs. the
likelihoodofaKafalsefromanothersource(possibleradardetector).
Ka RSID feature will educate you to the common Ka speed radar guns
by displaying and announcing the nominal police radar frequencies
of 33.8GHz / 34.0GHz / 34.3GHz / 34.7GHz / 35.5GHz. Ka alerts that
do not fall into the common Ka speed radar windows will be reported
only as Ka. NOTE: This product is not a frequency counter. The unit
will categorize the received Ka signal and select the appropriate
information. Treat every Ka alert with caution.
LSID (Laser Signal IDentifier)
IdentifytheLasergun’spulserateorPPS(PulsesPerSecond)thatis
transmitted by the speed laser gun. LSID may also be used to identify
other forms of laser sources such as LACC (Laser Assisted Cruise
Control)systemsfoundinsomehighendvehicles.IftheLaserPPS
information displayed is due to another source such as local airports
or LACC, LSID allows you to Lock Out this rate from giving you the
continuous audio alert during this and any new encounter of the same
rate.ToLockOutaPPS,presstheQuietbuttonduringtheLaseralert.
This will place an * on the screen beside the PPS rate and Lock Out
this signature ID. Any new encounter with the same Laser Signature
ID will provide the display information and two quick beeps. NOTE:
Common Laser PPS rates used in the USA are 100 / 125 / 130 / 200
/ 238 / 380Hz. Other Laser PPS rates used outside the USA include
600Hz. Caution: Do not lock out a PPS rate if it is close to known
speed laser guns.
Segmented Selectable Laser Receiver
If these alerts are bothersome, you may wish to make note of the PPS
rate for these occurrences. The laser validation windows are separated
into segments allowing for customization.
Segment Pulse Rate
Laser Area 1: 20Hz to 950Hz
Laser Area 2: 2600Hz to 3200Hz
Laser Area 3: 3800Hz to 4200Hz
Laser Area 1 covers the traditional laser guns used in North America.
Laser Area 2 and 3 cover laser guns recently approved for use in North
America. You can change the selection from yes to no individually in
option mode.
POP
™
Mode Alerts
Because POP
™
Mode radar utilizes the same
K or Ka band frequencies, POP
™
Mode Alerts will be displayed as
regular radar alerts.
Pulse Protection
®
Pulse(orinstant-on)radarismoredifficulttodetectthan
conventional radar because it remains ‘off’ until activated
to measure the speed of a targeted vehicle. When a pulse
type transmission is detected, your Whistler detector sounds an
urgent 3-second audio warning.
Displays Shows:
After the 3-second pulse alert, the standard alert pattern
continues for as long as the signal is present. It is important
to respond promptly to a pulse alert, since warning time may
be minimal.
TROUBLESHOOTING
YourWhistlerdetectorisexpertlyengineeredanddesigned
toexactingqualitystandardstoprovideyouwithreliable,
trouble-free operation. If your unit has been correctly
installed following the guidelines in this manual, but is not
operating optimally, please refer to the troubleshooting
guide below.
PROBLEM: No display or audio.
• Check fuse in plug; replace if necessary with a 3 amp, 3AG type.
• Check fuse for lighter socket; replace if necessary.
• Make sure lighter socket is clean.
PROBLEM: Unit alarms when vehicle hits bumps.
• Check for loose lighter socket; tighten and clean.
• Check connections at both ends of the power
cord. Substitute another cord to determine if
the cord is defective. Return defective cord to
the factory.
PROBLEM: Audio alerts are not loud enough.
• CancelAutoQuietModeorCityMode.
• Checkaudiolevelsetting(seepage8).
•CheckSpeedSelectableAutoQuietsettinginoptionmode.
PROBLEM: Unit falses too much.
•IfalarmsarePOPKa,switchPOPModetooff.
•Iftheaboveoptiondoesn’thelp,useahigherFiltersetting.
•IfalarmsareXorKbandandduetoradarbasedtraffic
flow sensors or radar based vehicle blind spot detectors,
turn TFSR on.
Laser Facts
It’s well documented that many radar guns
cannot reliably provide the speed of a targeted vehicle
that is traveling in a group of vehicles. In contrast, a
laser gun can target a specific vehicle out of a line of
traffic and determine its speed. The advantage of laser
over radar in terms of
target identification is the result of the laser gun’s narrow
beam. A radar gun’s transmission can cover more than a
four-lane highway at a distance of 1,000 feet, compared
with a laser gun’s transmission which covers about 3 feet
at the same distance. For best protection, keep these
points in mind:
• Because the vehicle’s license plate or headlights
are the laser gun’s primary targets, mounting the
Whistler detector on the dashboard can improve
laser detection at short range.
• Do not follow closely behind any vehicle you cannot
see through. If you can’t see past a vehicle ahead of
you, chances are your detector can’t either.
• The receiving range of your laser detector will not be
the same as a radar detector.
• Laser guns are most often used at short range.
Whistler Laser-Radar detectors receive all current laser
guns which operate at a laser wavelength of 905 +/- 50nm
including but not limited to the following:
SPEED MONITORING
Laser Tips
If you are the targeted vehicle, a laser gun can
often determine your speed within a few
seconds after you receive an alert. In this
situation, there is generally no time to safely
adjust your speed. However, if you are traveling
near or behind the targeted vehicle and receive
an alert, response time should be sufficient.
Any laser alert, regardless of duration, requires
immediate action.
Radar Facts
A radar gun operates by transmitting radio
waves at certain frequencies which reflect off
objects and are picked up by the radar gun’s
receiving section. When a radar beam reflects
off a moving target, a measurable frequency
shift occurs. The radar unit converts this shift into
miles per hour to determine your vehicle’s speed.
Currently, the FCC (Federal Communications
Commission)permitsoperationoftrafficradar
gunsatXBand(10.500-10.550GHz),KBand
(24.050-24.250GHz),andKaBand(33.400-
36.000GHz).
Note: A radar detector will only alarm if an
officer is transmitting on any one of the above
radar bands.
Other Speed Detection Systems
Several techniques other than radar or laser are
used to measure vehicle speeds. When these
methods are being used, no detector can provide
a warning. These techniques include:
• Pacing - A patrol car drives behind you and
matches your driving speed.
• Vascar/Aircraft - The police measure the time
it takes your vehicle to travel a known distance.
SPEED MONITORING
Radar Detector Detectors: VG-2, Spectre
The Interceptor VG-2 or simply VG-2, is one type of
microwave receiver used by Police to detect signals
radiated by the local oscillator of a radar detector.
Because its purpose is to identify persons driving with
radar detectors, these devices are known as a “radar
detectordetector”(RDD).
An RDD is the primary tool used by the police to identify
radar detector equipped vehicles. If caught in a state
orcountrywheredetectorsareillegal(seepage20),
drivers risk losing their radar detector and receiving a
fine. In addition, instant-on radar is almost always used
in combination with an RDD, leaving unsuspecting
motorists vulnerable to receive two tickets; one potential
for speeding, and the other for possession of a detector.
Note: The newest tool Police have to detect radar
detectors is called Spectre. Spectre can detect the
majorityofundetectable(VG-2)laser/radardetectors
on the market.
It is the responsibility of the individual radar detector
user to know and understand the laws in your area
regarding the legality of the use of radar detectors.
WARRANTY INFORMATION
Consumer Warranty
This Whistler Laser-Radar detector is warranted to
the original purchaser for a period of two years from
the date of original purchase against all defects in
materials and workmanship. This limited warranty
is void if the unit is abused, modified, installed
improperly, or if the housing and/or serial numbers
have been removed.Therearenoexpresswarranties
covering this product other than those set forth in
thiswarranty.Allexpressorimpliedwarrantiesforthis
product are limited to the above time. Whistler is
not liable for damages arising from the use, misuse,
or operation of this product.
Note: Units that cannot be repaired will be replaced with the same or
similar model. Replacement unit’s warranty will be based on the original unit’s
purchase date.
SPEED MONITORING
Service Under Warranty
During the warranty period, defective units will
be repaired without charge to the purchaser when
returned with a dated store receipt to the address
below. Units returned without a dated store
receipt will be handled as described in section
“Service Out Of Warranty.”
Due to the specialized equipment necessary for
testing a Laser-Radar receiver, there are no
authorized service stations for Whistler brand
detectors other than Whistler.
When returning a unit for service, please follow
these instructions:
1. Ship the unit in the original carton or in a
suitable sturdy equivalent, fully insured, with
return receipt requested to:
Whistler Repair Dept.
1412 South 1st St.
Rogers, AR. 72756
Please allow 3 weeks for turn around time.
Important: Whistler will not assume
responsibility for loss or damage incurred in
shipping. Therefore, please ship your unit
insured with return receipt requested.
CODs will not be accepted!
2. Include with your unit the following
information, clearly printed:
• Your name and street address (for shipping
viaUPS),adaytimetelephonenumberand
an email address, if applicable.
• A detailed description of the problem
(e.g., “Unit performs self-test but does not
respondtoradar”).
• A copy of your dated store receipt or bill
of sale.
WARRANTY INFORMATION
3. Be certain your unit is returned with its serial
number. For reference, please write your unit’s
serial number in the space provided on page
27 of this manual.
Units without serial numbers are not covered under warranty.
Important: To validate that your unit is within
the warranty period, make sure you keep a copy
of your dated store receipt. You may register
your warranty online at www.whistlergroup.com,
however, for warranty verification purposes,
a copy of your dated store receipt must
accompany any unit sent in for warranty work.
Service Out of Warranty
Units will be repaired at “out of warranty”
service rates when:
 •Theunit’soriginalwarrantyhasexpired.
 •Adatedstorereceiptisnotsupplied.
 •Theunithasbeenreturnedwithoutitsserial
number.
 •Theunithasbeenabused,modified, 
installed improperly, or had its housing
removed.
The minimum out of warranty service fee for
yourWhistlerdetectoris$85.00(U.S.).Ifyou
require out of warranty service, please return
your unit as outlined in the section “Service
Under Warranty” along with a certified check
or money order. Payment may also be made
byMasterCard,VISA,orAmericanExpress;
personal checks are not accepted.
In the event repairs cannot be covered by the
minimum service fee, you will be contacted by
a Whistler technical service specialist who will
outline options available to you.
WARRANTY INFORMATION
If you elect not to have your unit repaired, it will be
returned to you along with your certified check or
money order.
Important: When returning your unit for service, be
certain to include a daytime telephone number and an
emailaddress(ifapplicable).
Customer Service
If you have questions concerning the operation of your Whistler
detector, or require service during or after the warranty period,
please call Customer Service at:
1-800-531-0004
Representatives are available to answer your questions Monday
-Fridayfrom8:00a.m.to5:00p.m.(CT)orvisitth eF.A .Q.’sat
www.whistlergroup.com.
SPECI FI C ATIONS
Laser Wavelength:
905+/-50nanometers(nm)
Radar Frequencies:
10.500-10.550GHz(XBand)
24.050-24.250GHz(KBand)
33.400-36.000GHz(KaSuperwideband)
Operating Temperature Range:
-10 C to +70 C (-41Fto+158F)
Power Requirements:
Operational 12 to 15 volts DC, 250mA nominal Vehicle
Battery Saver, 30mA nominal.
Patents can be viewed here:
www.whistlergroup.com/pat
POP
™
Mode is a trademark of MPH Industries, Inc.
SWS
™
Mode is a trademark of Safety Warning Systems L.C.
Specifications are subject to change without notice.
WARRANTY INFORMATION
OWNER’S MANUAL
• Ultra Lyte
• LTI 20-20
• LTI TruSpeed
®
S
• Laser Ally
• Pro Laser
™
I II III
• Laser Atlanta
®
Stealth Mode
The Whistler Group Corporate Headquarters
1716 SW Commerce Dr. Ste. 8 • Bentonville, AR 72712
Tel 479.273.6012 • Fax 479.273.2927
Customer Return Center
1412 South 1st St. • Rogers, AR 72756
Customer Service Tel 800.531.0004
www.whistlergroup.com
P/N 260044 06A14 © 2014 The Whistler Group, Inc.
CR90
HIGH Performance
LASER-RADAR
DETECTOR
write serial number in the space provided
Stay Alert Feature
The Stay Alert Feature is designed to test a driver’s
alertness.Toengage(whentheunitisnotalarming):
• PressandholdtheCitybuttonfor 
 approximately2seconds.Releasethebutton
during or immediately after the alert is given.
Display Shows:
Within 30-60 seconds, two beeps are sounded; to
show alertness, the driver must press either the City,
Menu,orQuietbuttonswithin3-5seconds.Ifabutton
is pressed within 3-5 seconds, the cycle is repeated.
If a button is not pressed within 3-5 seconds, an
alarm sounds.
Display Shows:
• PresstheDarkbuttontoexittheStayAlert
feature.
WARNING!!! Stay Alert is NOT intended as a
substitute for adequate rest. You should NOT
operate a vehicle if you are drowsy. During
extendedperiodsofvehicleoperation,you
should take frequent breaks. Improper reliance
on the Stay Alert feature may result in vehicle
damage, personal injury or death.
NEVER OPERATE
A VEHICLE
IF YOU ARE
DROWSY!
If difficulties occur which cannot be solved by information in this
Troubleshooting Guide, please call Whistler Customer Service
at1-800-531-0004orvisitourF.A.Q.pageatwww.whistlergroup.
com, before returning your unit for service.
Care and Maintenance
Duringthesummermonths,avoidprolongedexposuretodirect
sunlight by removing your unit from the dash when your vehicle
isparkedforanextendedperiodoftime.Donotspraywater,
cleaners, or polishes directly onto the unit. The spray may
penetrate through the openings and damage the unit. Also, do
notuseanyabrasivecleanersontheunit’sexterior.
Are Detectors Legal?
In Most States YES.
Laser-Radardetectorsarelegalineverystate(exceptVirginia
and Washington, D.C., which have local regulations restricting
theuseofradarreceiversinanyvehicle)whenusedin
automobilesorlighttrucks(under10,000lbs.).TheFederal
HighwayAdministration(FHWA)issuedaregulation,effective
January, 1994 which prohibits radar and laser detector use in
vehicles over 10,000 lbs. Prior to the FHWA regulation, laws
existedinNewYorkrestrictingtheuseofradardetectorsintrucks
over 18,000 lbs. and in Illinois in trucks over 26,000 lbs.
FCC Information
FCC ID: HSXWH20
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1)thisdevicemaynotcauseharmfulinterference,
(2)thisdevicemustacceptanyinterference
rec eived , including interference that may cause
undesired operation.
Important: FCC requirements state that changes or modifications
notexpresslyapprovedbyWhistlercouldvoidtheuser’s
authority to operate the equipment.
POP
™
Mode
POP™ Mode is a feature on some radar guns operating on K
and Ka bands. When the gun is in POP™ Mode and activated, a
brief burst of energy, less that 1/15 of a second, is transmitted
and the vehicle’s speed is quickly acquired. A detector without
POP™ Mode detection capability cannot respond to this brief
transmission.
27
26
25
24
23
22
21
20
19
18
17
1615

Whistler CR90 Specifications

General

Brand	Whistler
Model	CR90
Category	Radar Detector
Language	English