Xylem CentriPro Aquavar SOLO 2 - User Manual

How do I size the Aquavar SOLO² for the appropriate pump/motor combination?
Can I use a 208V motor?
Can I run the Aquavar SOLO² up to 80 HZ?
What are the recommended spare parts for an Aquavar SOLO²? Can I repair?
Can I mount the Aquavar SOLO² controller in an outside environment? If so what are the maximum conditions
allowed?
What if my Aquavar SOLO² controller is not putting out the recommended output in GPM?
Why does my pressure drop suddenly during start up?
What about interference with AM radio or other devices?
Is the unit sensitive to lighting strikes or voltage disturbances?
Can I use the Aquavar SOLO² with generators?
Can I use GFCI protected power for the Aquavar SOLO² controller?
Is my pressure transducer sensitive to stray voltage and electrical disturbances?
What type of breakers or fuses should I use?
Can I use aluminum wire (pre-existing or new installation)?
Will the Aquavar SOLO² increase the life of my pump and motor compared to a conventional switch system?
Is the pressure transducer operation sensitive to poor signal and electrical disturbances?
Can submersible cable (copper 75°) be used to extend the length of transducer?
When sizing the Aquavar SOLO² for use with another motor manufacturer, is it recommended to upsize to the next size
Aquavar SOLO², to maximize the performance of the pump?
Can the Aquavar SOLO² run without the pressure transducer/or if there is a transducer failure?
What accessories are offered for use with the Aquavar SOLO²?
Are 80 Hz performance curves available?
Can I use a oat switch instead of a pressure transducer with the Aquavar SOLO²?
How far can the oat switch be from the drive? What is the maximum total length for pressure transducer cable?
Is the pressure transducer affected by a vacuum, or by water hammer?
What causes a pressure uctuation of more than 5 PSI (assuming the controller is set at 5 PSI not 20)?
What is the proper orientation and location for the pressure transducer?
How can the Aquavar SOLO² be used to develop a well system?
Can the Aquavar SOLO² be used for surface mount booster applications? What are the motor electrical requirements?
Can I run a 50 Hz motor with the Aquavar SOLO² or use the Aquavar SOLO² in a 50 Hz application?
Can I use a 208V input on the Aquavar SOLO²?
Why would I use Dual Set points and how do I set it up?
How do I program output relays?
Can the Aquavar SOLO² run a chlorinator or another external metering pump?
Aquavar SOLO
2
FREQUENTLY ASKED QUESTIONS / AQSOLO2FAQ

Summary

Aquavar SOLO2 Frequently Asked Questions

Sizing and Motor Compatibility

Guidance on sizing the Aquavar SOLO2 for pump/motor combinations, using 208V motors, and operating up to 80 Hz.

Installation and Environment

Covers mounting the controller outdoors, recommended spare parts, and handling interference.

Performance and Troubleshooting

Addresses issues like low output, pressure drops, voltage sensitivity, and motor rotation.

Electrical Considerations and Protection

Discusses sensitivity to lightning, generators, GFCI power, and correct breaker/fuse types.

System Integration and Longevity

Explains how the SOLO2 extends pump life, transducer sensitivity, and using submersible cable.

Transducer and Cable Management

Details transducer sensitivity, cable length limits, and proper orientation for optimal performance.

Operational Modes and Accessories

Covers running without a transducer, using float switches, and available accessories.

System Development and Applications

Explains using the SOLO2 for well systems, booster applications, and 50 Hz operation.

Advanced Configuration and Control

Covers dual set points, programming output relays, and resetting fault history.

Xylem CentriPro Aquavar SOLO 2 Specifications

General

Brand	Xylem
Model	CentriPro Aquavar SOLO 2
Category	Water System
Language	English