Yaesu FTDX10 Information For Customers Operating

FTDX5000 / FTDX3000 / FTDX1200
1. Turn the transceiver OFF.
2. Press and hold in the
[
MENU
]
and
[
C.S
]
buttons while
turning the transceiver ON.
The green LED Indicator will blink with intervals of 0.5 sec
(0.5 sec ON, 0.5 sec OFF).
3. Press and release the
[
MENU
]
button, and the Green LED
Indicator will now blink with interval of 1 sec (1 sec ON, 1
sec OFF).
4. Press and hold in the
[
MENU
]
button, and the radio will re-
start automatically. Once restarted the change of 5 MHz fre-
quency conguration will have been completed successfully.
Power Switch
C.S Button
LED Indicator
MENU Button
FTDX5000
MENU Button
C.S Button
Power Switch
LED Indicator
FTDX3000
MENU Button LED Indicator
C.S Button
Power Switch
FTDX1200
FT-891
1. Turn the transceiver OFF.
2. Press and hold in the
[
F
]
and
[
QMB
]
buttons while turning
the transceiver ON.
The green LED Indicator will blink with intervals of 0.5 sec
(0.5 sec ON, 0.5 sec OFF).
3. Press and release the
[
F
]
button, and the Green LED Indica-
tor will now blink with interval of 1 sec (1 sec ON, 1 sec OFF).
4. Press and hold in the
[
F
]
button, and the radio will re-start
automatically. Once restarted the change of 5 MHz frequency
conguration will have been completed successfully.
F ButtonLED Indicator
Power Switch
QMB Button
FT-991A
1. Turn the transceiver OFF.
2. Press and hold in the
[
F
]
and
[
MODE
]
buttons while turning
the transceiver ON.
The green LED Indicator will blink with intervals of 0.5 sec
(0.5 sec ON, 0.5 sec OFF).
3. Press and release the
[
MODE
]
button, and the Green LED Indi-
cator will now blink with interval of 1 sec (1 sec ON, 1 sec OFF).
4. Press and hold in the
[
MODE
]
button, and the radio will re-
start automatically. Once restarted the change of 5 MHz fre-
quency conguration will have been completed successfully.
MODE Button
LED Indicator
Power Switch
F Button
* The FT-991A is an HF and VHF/UHF transceiver. Please note that the default ARS UHF repeater frequency coverage
and shifts for this model are di󰀨erent from normal UK usage. Selecting the “C2” conguration as below will enable cor-
rect repeater coverage and shifts for UK operation.
ARS Conguration “B2”
Factory Default Setting
ARS Conguration “C2”
Selectable Setting
ARS Frequency Range: 438.20 MHz - 439.45 MHz
(
- shift
)
Repeater Shifts: 7.6 MHz
ARS Frequency Range: 433.00 MHz - 433.40 MHz
(
+ shift
)
434.60 MHz - 435.00 MHz
(
- shift
)
Repeater Shifts: 1.6 MHz
Caution:
• When changing 5MHz and 70MHz* band frequencies according to the procedures above, all saved data, such as
Menu and Memory settings, will be deleted. If you need to change the 5MHz and 70MHz* bands after using the
radio, make sure to back up your registered data or make a written note, before applying the setting change.
• The current 5MHz and 70MHz* band frequency range setting (B2 or C2) is NOT changed, even when executing the
“Full Reset” procedure to factory defaults as described in the Operating Manual.

Yaesu FTDX10 Specifications

General

Type	HF/50 MHz Transceiver
Antenna Impedance	50 Ohms
Supply Voltage	13.8 V DC ±15%
IF DSP	Yes
Modes	AM, FM
RF Power Output	100 W (HF)
Display	5-inch Full-Color Touch Panel
Dimensions	266 x 263 mm
Weight	5.9 kg
IF Rejection	70 dB or better
Image Rejection	70 dB or better
Receiver Type	SDR (Software Defined Radio)