MF93D
Let’s go
Getting started with your device.
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
LEGAL INFORMATION
Copyright © 2013 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, includ-
ing photocopying and microlm, without the prior written permission of
ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to
make modications on print errors or update specications without prior
notice.
Version No. : R1.0
Edition Time : 2013.04
NOTE:
Do not use the device in an enclosed environment or where heat dis-
sipation is poor. Prolonged work in such space may cause excessive
heat and raise ambient temperature, which may lead to automatic shut-
down of the device for your safety. In the case of such event, cool the
device in a well-ventilated place before turning on for normal use.
Getting to Know Your Device
Appearance
The following gure is only for your reference. The actual product may
be different.
External Antenna Connector
Micro USB Port
OLED Screen
Power Switch
(U)SIM Card Slot
RESET Button / microSD Card Slot
WPS Button
NOTES:
• microSD logo
is a trademark of SD Card Association.
• Please use the original external antenna if necessary.
Indicators
When the device is powered on, the following icons will appear on the
OLED screen, with the corresponding indicates listed in the table be-
low:
Icon Indication
Network signal strength.
2G/3G/4G
Network type. 2G, 3G, 4G icon will appear on the OLED
screen according to the network being connected.
Connect to the Internet automatically.
Connect to the Internet manually.
Roaming network indication.
New message received.
Wi-Fi Status and number of the connected users.
Battery power indication.
Connection Scenario
Your device supports two methods to go to Internet and supports multi-
clients for surng on the Internet at the same time. The following gure
is only for your reference.
• 4G Mode: Use your (U)SIM card to access the Internet.
• Internet Wi-Fi Mode: Your device will connect to other WLAN de-
vice (hotspot device, wireless router, etc.) via Wi-Fi to access the
Internet. The WLAN device has already connected to the Internet.
NOTE:
The subnet must be deferent between your device and other WLAN
device.
Installing Your Device
1. Insert the SIM card.
IMPORTANT: Your device does not support Micro/Nano or any other
nonstandard SIM cards. To avoid device damage, please do not use
them.
2. Insert the microSD card.
1) Open the microSD card cover.
NOTE:
Do not pull the cover rudely, as it is connected with the device.
2) Insert the microSD card into the microSD slot. The following picture
shows the correct inserting direction. You will hear a click when the
microSD card locks in place.
3) Close the microSD card cover.
Connecting to Your Device
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search for the
available wireless networks.
NOTE: Please set the client to obtain an IP address automatically refer-
ring to the chapter “Conguring Your PC”, and then the client will get an
IP address like “192.168.0.100”.
3. Select the SSID of your device, and then click Connect. The follow-
ing picture is only for your reference.
4. Input the password, and then click Connect.
NOTE:
• There may require the password for Wi-Fi connection, please check
the label on your device to get the default.
• Double press the WPS button, and then the SSID and Wi-Fi key
will display on the OLED screen.
5. Wait a moment, and then the client will connect to your device suc-
cessfully.
Via USB Cable
1. Connect to the device.
2. Power on your device.
3. The OS detects and recognizes new hardware and nishes the in-
stallation automatically.
NOTE: If the Windows operating system does not launch installation
automatically, you can run the installation program in path of My Com-
puter > ZTEMODEM.
4. Wait a moment, and then the client will connect to your device suc-
cessfully.
Accessing the Internet
4G Mode
After the client connected to your device successfully, you can access
the Internet in the Automatic or Manual mode. The default mode is
Automatic.
Mode Operations
Automatic
Your device will connect to the Internet automatically,
and your clients can surf on the Internet directly.
Manual
Login the webGUI conguration page, and select Set-
tings > Network Settings > Dial-up Settings > Man-
ual, and then click Home > Connect / Disconnect.
NOTE:
If you want to modify the detailed parameters of your device, please
login the webGUI conguration page by visiting http://192.168.0.1 or
http://m.home. The default password is admin.
Internet Wi-Fi Mode
1. Login the webGUI conguration page.
2. Select Settings > Internet Wi-Fi.
3. Set the Internet Wi-Fi Switch and Preferred Network, and then
click Apply.
NOTE:
You need to Enable the Internet Wi-Fi Switch and select Wi-Fi.
1 2 3 4 5 6 7 8 9
To Next Page
Need help?
General
