(enter) keypad to enter the value of the digit and advance to
the next digit.
7. Press the START (enter) keypad with the last active digit. The
next option, AtS 9, will appear in the display.
Vend Price 9 AtS 9
This option allows the owner to set the vend price for DELI-
CATES COLD. This vend price will be shown in the display
when DELICATES COLD is selected.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until AtS 9 appears in the
display.
4. The DELICATES and COLD LEDs will be lit to show which
cycle/temperature price is being programmed.
5.
When AtS 9 appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
6. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
7. Press the START (enter) keypad with the last active digit. The
next option, dEn 1, will appear in the display.
Cycle Modifier Key 1 MEDIUM Vend
Price Adder ACNP 1
This option allows the owner to add to the vend price for the ME-
DIUM modifier key. This price is added onto the cycle price.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
ACNP 1 appears in the display.
4. TheMEDIUM modifier LED will be lit to show which price is
being programmed.
5.
When ACNP 1 appears in the display, press the START (en-
ter) keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
6. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
7. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Modifier Key 2 HEAVY Vend Price
Adder ACNP 2
This option allows the owner to add to the vend price for the
HEAVY modifier key. This price is added onto the cycle price.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until ACNP 2 appears in
the display.
4. The HEAVY modifier LED will be lit to show which price is
being programmed.
5.
When ACNP 2 appears in the display, press the START (en-
ter) keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
6. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
7. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price Decimal Point Ats dP
This option allows the owner to enable a decimal point to show
up in the vend price at one of two locations. For example, a vend
price of 200 can be display with a decimal point as 2.00 or
0.200.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until Ats dP appears in
the display.
4.
When Ats dP appears in the display, press the START (en-
ter) keypad.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
39 Part No. 204370ENR1
To Next Page
Loading...
Need help?
General