Atlas Copco Power Focus 3000 - User Manual

User guide
Power Focus
Atlas Copco Industrial Technique AB
9836 3123 01
Software release W10.9 SR3
Edition 18.2
2013-03

Atlas Copco Power Focus 3000 Specifications

General

Supply voltage	100-240 VAC
Supply frequency	50/60 Hz
Power supply voltage	24 VDC
Operating temperature range	0°C to +45°C
Storage temperature range	-20°C to +70°C
Communication	Ethernet
Relative humidity	Max 90% non-condensing
Communication interface	Ethernet, USB, RS-232

Summary

General safety instructions

Electrical safety

Earthed tools must be plugged into a socket that has been properly installed and earthed according to appropriate regulations.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power tool.

Service

Tools should only be serviced by qualified repair personnel. Service or maintenance performed by unqualified personnel could expose users to serious personal injury.

Getting started with ToolsTalk PF

Installing ToolsTalk PF

ToolsTalk overview

Configuring ToolsTalk settings

Describes settings for communication, application, printout, and PF list.

Connecting a PF

Details connection possibilities: Ethernet TCP/IP, Serial RS232, and USB.

Storing programming on file

Offline

Pset

Create new Pset;Open Pset

Describes how to create or open a Pset configuration.

Autoset

Explains the Autoset function for easy Pset programming.

Quick programming

Provides a fast and simple way to configure a Pset.

Programming help

Programming

Details how to select control strategy and set other parameters.

PVT comp with snug

Describes the PVT comp strategy with snug.

Tightening strategies

Provides a generic description of supported tightening strategies.

Rehit detection

Programming +

Covers applications for additional Pset functionality.

Pset setup

Accesses parameters for administration, results, and comments.

Statistic programming

Defines conditions for statistical calculations.

Running a Pset

Multistage

Create new Multistage;Open Multistage

Describes how to create or open a Multistage configuration.

Job

Job concepts

Job configuration

Details how to configure a Job group, Job reference, and Job client.

Creating a new Job

Select Job

Functions in the Job monitor

Unlock the tool

Describes how to unlock the tool by selecting a new Job, deleting Jobs, or selecting Job off.

Controller

Information

Configuration

Details settings for Select source, Tightening, Loosening, and Positioning.

Network

Explains how Power Focus uses Ethernet and serial communication.

Memory

Explains memory configuration options and the reset process.

Accessibility

Tool

Tool information

Tool configuration

Details configuration for tool start, accessory bus, sound, buttons, and LEDs.

Tool diagnostic

Covers sensor tracking, peripherals, and wireless connection diagnostics.

Tool maintenance

Provides information on calibration, service, and open-end tuning.

Motor tuning

Disconnect tool

Tool lock functionality

Describes internal and external methods for locking tools.

Accessories

Digital I;O

Covers digital I/O capabilities and configuration.

I;O bus

Describes I/O bus capabilities and information.

Tool bus

Provides information and configuration for the tool bus.

Sync

Sync prerequisites and limitations

Outlines requirements and limitations for Sync groups.

Hardware configuration

Describes how to connect PF units in a Sync group via the I/O-bus.

Sync configuration

Details configuration steps for Sync groups.

Troubleshooting

Provides solutions for common Sync group issues.

Identifier

Identifier concepts

Explains the identifier function, ways to use it, and related terms.

Identifier prerequisites and details

Covers prerequisites for significant strings and incoming data.

Configuration of identifier functions

Covers identifier configuration, memory, and monitor functions.

Fieldbus

General setup

Covers general fieldbus setup, including type selection.

View fieldbus information

From PF setup and to PF setup

Explains bitmap configuration for data transfer.

Storing fieldbus configuration

Disable fieldbus carried signals

Fieldbus data format

Fieldbus selector configuration

Select Pset from fieldbus and set batch size

Fieldbus information

Logic Configurator

Logic operators and function blocks

Logic Configurator setup

Details the steps for setting up a Logic Configurator sheet.

Simulation

Statistics

Result parameters

Statistical results

Statistic alarm

Describes alarm limits based on x̄ and R calculations.

Trend deviation alarm

Calculation of UCL and LCL

Calculation of mean values

Calculation formulas

Constants for calculation of SPC variables

Quick reference guide

Tq con

Tq con;ang mon

Tq con;ang con (AND) and Tq con;ang con (OR)

Ang con;tq mon

Reverse ang

Rotate spindle forward and Rotate spindle reverse

Home position forward and reverse

DS con

Quick step

Ergo ramp

Snug gradient

Describes the Snug gradient strategy.

Parameter list

Pset

Lists Power Focus parameters for Pset.

Sync

Lists parameters related to Sync group list, tightening, loosening, and OK time.

Multistage

Lists parameters for Multistage setup and programming.

Identifier

Lists parameters for identifier setup.

Job

Lists parameters for Job setup and programming.

Fieldbus

Lists parameters related to fieldbus type and data length.

Controller

Lists parameters for Controller information, configuration, network, COM ports, display, memory, accessibility.

Tool

Lists parameters for Tool information, configuration, diagnostic, and maintenance.

Buzzer configuration

Sound configuration