10
ENGLISH
(Original instructions)
u Remove hand from guard lever and firmly grip secondary
arm to allow you to resist kickback if it occurs.
u Make sure blade is not in contact with cutting surface
before starting saw.
u Start the motor, allow saw to come to full speed, and then
material to be cut. Advance saw along the cutting line until
u Release trigger and allow blade to stop completely before
withdrawing the blade from the material.
u When starting each new cut, repeat as above.
Troubleshooting
Problem Possible Cause Possible Solution
Unit will not start.
Battery pack not
installed properly.
Battery pack not
charged.
Check battery pack
installation.
Check battery pack
charging requirements.
Battery pack will
not charge.
Battery pack not
inserted into charger.
Charger not plugged in.
Surrounding air
temperature too hot or
too cold.
Insert battery pack into
charger until LED appears.
Plug charger into a
working outlet. Refer
to “Important Charging
Notes” for more details.
Move charger and battery
to a surrounding air
teperature of above 40
degrees F (4.5°C) or
below 105 degrees F
(+40.5°C).
Unit shuts off
abruptly.
Battery pack has
reached its. maximum
thermal limit.
Out of charge. ( To
maximize the life of the
battery pack it is
designed to shutoff
abruptly when the
charge is depleted.)
Allow battery pack to cool
down.
Place on charger and
allow to charge.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and re-
cycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
address indicated in this manual. Alternatively, a list of author
ised BLACK+DECKER repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
BDCCS18
Input voltage
V
ac
18
No-load speed
min
-1
3700 RPM
Max depth of cut
mm 43
Max depth of cut at 45º bevel
mm 35
Blade diameter
mm 140
Blade bore
mm 12.7
Blade tip width
mm 2.0
Weight
kg 2.5
L
pA
(sound pressure) 76.0 dB(A), Uncertainty (K) 3 dB(A)
L
WA
(sound power) 87.0 dB(A), Uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Cutting wood (a
h, W
) 1.5 m/s
2
, uncertainty (K) 1.5 m/s
2
To Next Page
Loading...
Need help?
General
