English | 15
u Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
u Use suitable detectors to determine if there are hid-
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
u Always wait until the power tool has come to a com-
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
u In case of damage and improper use of the battery, va-
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
u Do not open the battery. There is a risk of short-circuit-
ing.
u The battery can be damaged by pointed objects such
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
u Only use the battery with products from the manufac-
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
u Switch the power tool off immediately if the applica-
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
u Caution! When using the power tool with Bluetooth
®
, a
fault may occur in other devices and systems, aero-
planes and medical devices (e.g. pacemakers, hearing
aids). Also, damage to people and animals in the im-
mediate vicinity cannot be completely excluded. Do
not use the power tool with Bluetooth
®
in the vicinity of
medical devices, petrol stations, chemical plants,
areas with a potentially explosive atmosphere or in
blasting areas. Do not use the power tool with
Bluetooth
®
in aircraft. Avoid using the product near
your body for extended periods.
The Bluetooth® word mark and logos are registered trade-
marks owned by Bluetooth SIG, Inc. and any use of such
marks by Robert Bosch Power Tools GmbH is under li-
cense.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for driving and loosening screws
and for drilling in wood, metal, ceramic and plastic. The GSB
is also designed for impact drilling in brick, masonry and
stone.
With the GCY 30-4 Bluetooth
®
Low Energy Module that is fit-
ted in the power tool, data and settings of the power tool can
be transferred between the tool and a mobile device by
means of Bluetooth
®
wireless technology.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Tool holder
(2)
Keyless chuck
(3)
Torque presetting ring
(4)
Operating mode presetting ring
(GSB 18V-60 C)
(5)
Gear selector switch
(6)
Belt clip
(7)
Battery
(8)
Battery release button
(9)
Worklight (LED)
(10)
Overload protector indicator
(11)
Universal bit holder
a)
(12)
Rotational direction switch
(13)
On/off switch
(14)
Handle (insulated gripping surface)
(15) Bluetooth® Low Energy Module cover GCY30-4
a)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless Drill/Driver GSR 18V-60 C GSB 18V-60 C
Article number
3601JG11.. 3601JG21..
Rated voltage V= 18 18
No-load speed
A)
Bosch Power Tools 1 609 92A 5U1 | (02.11.2021)
To Next Page
Loading...
Need help?
General