EasyManuals Logo

Bosch Indego XS 300 User Manual

Bosch Indego XS 300
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
9
Maintenance
Cleaning.
Before cleaning, some precautions have to be taken.
Always wear gardening gloves when handling or working near sharp blades.
Before working on your Indego or its docking station, make sure the mower is switched off using the isolator switch and
the power supply plug is removed from mains.
Clean your Indego and its docking station with a dry cloth or a soft and dry brush. Do not use water, solvents or polishes as
they can cause damage and will void the warranty.
Blade change.
Before attempting to replace the blades, please remember to follow the safety instructions.
Always wear gardening gloves when handling or working near sharp blades.
Before working on your Indego or its docking station make sure, the mower is switched off using the isolator switch and
the power supply plug is removed from mains.
Blades should be replaced when the cutting finish degrades, which should be at least every season.
Please use only original Bosch replacement blades and screws. Our original Bosch blades are reversible, so they can last up
to two seasons.
When replacing blades, make sure to replace the whole set including screws. Replacing single blades can affect the balance
of the cutting disc, which can lead to an increased noise level.
To make replacing the blades easier, the cutting disc can be locked, as shown in the picture (2).
Ensure a good fit of the blades that these can rotate freely during operation.
9.1
9.2
Winter storage.
Once the temperature is consistently below 5°C, your Indego and its docking station must be stored in a dry place between
a temperature of -20°c and 50°C. The garage is not providing sufficient protection for the mower and/or the docking station
during the winter. Do not place objects on the Indego or on its docking station.
Software updates.
We are continuously working on improvements of our products. In order to benefit from those as well as from any new
features, we recommend to keep the software of your Indego up to date.
All Indego models can be updated by using an USB stick and an USB cable. Connected models additionally have the ability
to receive software updates 'over-the-air' via the mobile network.
New software updates will be made available to all users via our Bosch Smart Gardening App (connected models only) and
our website (bosch-diy.com/indego-help). If you download the software from our website, you can find there instructions
on how install the software on your Indego. The instructions may change based on the requirements of the latest software
version. Therefore, please check the instructions before installing the software on your Indego.
Replacing the battery.
Indego S/S+ and M/M+ are fitted with a standard 18V 2.5Ah battery which can be replaced when needed. Your Indego will
only operate with Bosch 18V 2.5Ah batteries. Other batteries are not supported.
The battery should be replaced when the performance is degrading. Please refer to 8.8 for more information about the
battery. Please only replace the battery when necessary. Frequent opening and closing of the battery compartment can
compromise the pr
otection against water.
Do not let your Indego run without the battery compartment cover fitted as it can cause damage to the mower.
Damage caused by a not fitted cover is excluded from warranty.
9.5
9.3
9.4
!
GB
4746

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Bosch Indego XS 300 and is the answer not in the manual?

Bosch Indego XS 300 Specifications

General IconGeneral
Power sourceBattery
Battery voltage18 V
TypeRobotic lawn mower
Cutting width19 mm
Product colorBlack, Green
Cutting systemRotary blades
Maximum lawn area300 m²
Mulching function-
Maximum cutting height50 mm
Minimum cutting height30 mm
Suitable for slope up to27 %
Number of height positions3
Cutting clearance adjustmentYes
Weight and Dimensions IconWeight and Dimensions
Depth445 mm
Width364 mm
Height202 mm

Related product manuals