Clarion ARX5370R User Manual

- GOM PONENTS 3. Check for safety after repair.
Check that the screws,parts and wires are put back
PE-1531E-A securely in their original position after repair.Ensure
“Main unit ~~ See a 1 for safety reasons there is no possibility of secondary
: Mounting bracket 300-9677-00 1 ploblems around the repaired spots.
Parts bag SSS if extended damage is caused due to negligence of
’ Hook plate 331-0488-00 2 repair,the legal responsibility shall be with the pepe
(alternative part 330-8216-01 2) ing company.
Cable tie 335-0823-07 1 4. Caution in removal and making wiring connection to
Spacer 345-3653-01 1 the parts for the automobile.
Screw 716-0726-01 1 Disconnect the battery terminal after turning the igni-
A-lead 850-6688-50 1 tion key off.If wrong wiring connections are made with
DCP case 335-5331 -00 1 the battery connected, a short circuit and/or fire may
. . : occur.lf extensive damage is caused due to negligence
a To engineers In charge of repair of repair,the legal responsibility shal! be with the re-
or inspection of our products. li Actas ae
; ; ; 5. Cautions regarding chips.
Before repair or inspection,make sure to fol- Do not reuse removed chips even when no abnormal-
low
the
instructions
so
that
customers
and
ity
is
observed
in
their
appearance.Always
replace
Engineers
in
charge
of
repair
or
inspection
can
them
with
new
ones.(The
chip
parts
include
resistors,capacitors, diodes, transistors,etc). The nega-
tive pole of tantalum capacitors is highly susceptible
to heat,so use special care when replacing them and
check the operation afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron,make sure that
the iron tip temperature is around 270'C.Take care
not to apply the iron tip repeatedly(more than three
times)to the same patterns.Also take care not to ap-
ply the tip with force.
7. Turn the unit OFF during disassembly and parts
replacement.Recheck all work before you apply power
to the unit.
avoid suffering any risk or injury.
1. Use specified parts.
The system uses parts with special safety features
against fire and voltage.Use only parts with equiva-
lent characteristics when replacing them.
The use of unspecified parts shall be regarded as re-
modeling for which we shail not be liable. The onus of
product liability (PL) shall not be our responsibility in
cases where an accident or failure is as a result of
unspecified parts being used.
2. Place the parts and wiring back in their original posi-
tions after replacement or re-wiring.
.For proper circuit construction,use of insulation
tubes,bonding,gaps to PWB,etc,is involved.The wir-
ing connection and routing to the PWB are specially
planned using clamps to keep away from heated and
high voltage parts.Ensure that they are placed back
in their original positions after repair or inspection.
if extended damage is caused due to negligence dur-
ing repair,the legal responsibility shall be with the re-
pairing company.
Mm ADJUSTMENT
FM section
item
Procedure
Decnen
S-meter
1.
Input
the
98.1MHz/30dB
»
(400Hz-MOD
30%)signal.
SG
2.
Turn
on
the
power
swtch.
and,Press
the
AF button
and
CH6
button
at
the
same time.(TEST
MODE)
3.
Adjust the reading of
LCD
indicator
to
[30----00]
(3.
ov+0.
2V) by
VR1.
Tape section
instrumen
Dolby
level
1.
Playback
a
Dolby
level
test
tape(400Hz,200nWb/m),
and
connect
the
milli-
Milli-volt
meter
volt
meter
to
TP1(R)
and
TP2(L).
Test
tape
2.
ahs
VR401(R)
and
VR402(L)
to
obtain
an
output
of
300mV+14B.
(Dolby
Adjustment point
( Top side of main unit )
E
| Seeeec nest | |
# ;
ARX5370R -2-

Clarion ARX5370R Specifications

General

Brand	Clarion
Model	ARX5370R
Category	Cassette Player
Language	English