Clarion ARX9170R User Manual

ed programme type, using the EON data.
“The PTY function does not work unless the ROS
mode is turned on. “RDS” is lit on the display when
the RDS mode Is on.
“When in the traffic announcement standby mode, traf-
fic announcements have priority over PTY broadcasts.
*Some countries and stations do not transmit PTY and
EON data.
Selecting the PTY SEEK mode
1} Press the ADJ button,
2) Use the up and down buttons to select
“GENERAL”, then press the ENT button ff.
3) Use the left and right buttons fiflto select
ot lB ees | = Ba
4) Use the up and down buttons to select one
of the PTY codes, from “NEWS” to “OTHER
Mm”,
5) Press the ENT button &. “PTY” appears on
the display, the PTY SEEK operation begins,
and when a station is found, the selected
PTY is displayed.
“If there are no stations broadcasting programmes
of the selected programme type, the previous sta-
tion ts tuned in and the PTY standby mode is set
atitomatically,
Selecting the PTY standby mode (1)
t) Press the ADJ button.
2) Use the up and down buttons to select
“GENERAL”, then press the ENT button 7.
3) Use the left and right buttons {8to select
“PTY SEL".
4) Use the up and down buttons to select one
ee PTY codes, from “NEWS” to “OTHER
5) Press the ADJ button to return to the pre-
vious mode, “PTY” lights and the PTY stand-
by mode is set.
Selecting the PTY standby mode (2)
Follow steps t) to 3) in “Selecting the PTY standby
mode (1)” to select “PTY SEL”, then press one of
the direct buttons). The PTY standby mode for
the programme type stored at that button is set,
Presetting programme types
Follow steps 1) to 4) in “Selecting the PTY stand-
by mode (1)" to select the programme type, then
press one of the direct buttons(9 for more than 2
seconds, That programme type is stored in the
memory, and “P1 MEMO” appears on the display
14
(when direct bution “1” is pressed).
“ Six programme types can be stored, one each at but-
tons 1 to 6.
Canceling the PTY standby mode
To cancel the PTY standby mode, press the
PTY button for more than 2 seconds. “PTY”
tums off. To set the PTY standby mode again,
press the PTY button again for more than 2
seconds,
“When the PTY button is pressed while receiving a pro-
gramme of the selected programme type, PTY recep-
tion is canceled and the PTY standby mode is set.
PTY display function
Use this function to display the programme type
of the station currently tuned. Press the DISP
button [@) fo switch the display.
nw "
Sa ee is displayed # the PTY data cannot be
TA (Traffic Announcement)
function
This function automatically tunes in traffic
announcements when they start,
Press the TA button [2]. “TA” lights and the radio
starts
searching
for
stations
broadcasting
traffic
announcements.
To tum the TA function off, press the TA button
again. However, when the TA button is pressed
while a traffic announcement is tuned in, the
traffic announcement mode is cancelled and the
TA stand by mode is set.
* The traffic announcement standby mode is set when
there is (are) a station(s) broadcasting traffic announ-
cements.
“When a traffic announcement has started, "TRA
INFO" is displayed, after which the PS (Programme
Service name ) or the frequency appears.
“When a traffic announcement starts, the loudness
function
is
tumed
off
and
the
volume
is
automatically
set to the preset level.
*
When
the
TA
button
is
pressed
while
tuned
In
to
a
station
which
is
not
broadcasting
traffic
announce-
ments,
the
radio
searches
for
a
station
which
is
broadcasting
traffic
announcements.
“if
no
traffic
announcement
is
found,
“NO
TRA"
is
dis-
played,
Press
the
TA
button
to
cancel
the
TA
mode.
Preset scanning when “TA” is lit or flashing Listening to CDs
When the PS button {iis pressed while "TA" is lit 4) press the FUNC button @to select the CD
or flashing, only preset traffic announcement changer mode. Playback starts automatically.
stations are scanned.
wTAt te 4% ; * The pause mode is set when the CD changer
fulg ctore when, TA: leitor teeny mode is set after the power fs tumed on or while
en the AS button fis pressed for more than :
by elie while “TA" is A or flashing, only pre- the magazine Is being loaded in the CD changer.
set traffic announcement stations are stored. In these cases, press the play/pause button {ito
start playback.
Setting the volume for traffic
announcements and emergency
broadcasts
1} Press the ADJ button fig.
2) Use the up and down buttons [ito select back temporarily.
“UTILITY”, then press the ENT button i. 3) Use the direct buttons @to select the desired
3) Use the left and right buttons [to select “TA disc.
VOL ADJ".
4) Use the up and down buttons to adjust the
volume.
5) Press the ADJ button.
* This operation is only possible in the radio mode.
2) Press the play/pause button filto stop play-
“Nothing happens if a direct button corresponding
to the number of a magazine in which no disc is
loaded is pressed.
"When a disc which is currently playing is selected,
playback resumes from the first track on that disc.
4) Use the left and right buttons [ito select
; tracks,
Time display function (CT: Clock »>: Press this to start playback from the
Time) beginning of the next track.
The time can be displayed in areas broadcas- <4: Press this to move back to the beginning of
ting CT data. the current track. Press it again to move
Press the DISP button [8Jto switch the display. back to the beginning of the previous track.
~ Some countries and stations do not broadcast CT * Titles can be given to discs and displayed. It no
data. Also note that in some areas the displayed time title has been given, “--—-—-— "is displayed.
may be wrong.
*"CT-—:--—" is displayed when no CT data is being
received,
Fast forward and fast backward
Press and hold in the left and right buttons [ié.
b>: Press and hold this to move rapidly
CD Changer Operations Grward
<4: Press and hold this to move rapidly
When a separately sold CD changer backend:
(CDC605/CDC1205/CDC 1805) is connected, it
can be controlled from the ARX9170R,
CD-ROMs
*CD-ROMs cannot be played.
” The disc moves at 3 times the norma! speed after
the button is held in 1 second, at 30 times the nor-
mal speed after it is held in 3 seconds.
Scan function
When the SCN button fis pressed, “SCN”
appears on the display, and the first 10 seconds
of ail the tracks on the disc are played. Press
the SCN button again to stop scanning.

Clarion ARX9170R Specifications

General

Brand	Clarion
Model	ARX9170R
Category	Cassette Player
Language	English