Craftsman CMCCS620 User Manual

ENGLISH
14
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.
Accessories

WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with thisproduct.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Repairs
The charger and battery pack are notserviceable. There are
no serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a CRAFTSMAN
factory service center or a CRAFTSMAN authorized
service center. Always use identical replacementparts.
• FigureS- When supported at bothends. First, cut 1/3
down from the top overbuck. Then make the finished
cut by underbucking the lower 2/3 to meet the firstcut.
2nd CUT UNDERBUCK
(2/3 DIAMETER)
TO MEET 1st CUT
(TO AVOID PINCHING)
1st CUT OVERBUCK
(1/3 DIAMETER)
TO AVOID SPLINTERING
Fig. S
• When on a slope always stand on the uphill side of the
log. When “cutting through”, to maintain complete
control reduce the cutting pressure near the end of the
cut without relaxing your grip on the chain saw handles.
Don’t let the chain contact the ground. After completing
the cut, wait for the saw chain to stop before you move
the chain saw. Always stop the motor before moving
from cut tocut.
Versatrack™ (Fig. W)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.

WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ integral
hang hook or Versatrack™ Trackwall. A damaged
Versatrack™ integral hang hook or Versatrack™
Trackwall will not support the weight of the tool.

WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the integral hang hook. ONLY suspend
tool on the Versatrack™ Trackwall using the integral
hang hook.

WARNING: The Versatrack™ integral hang hook
is intended to mount the tool onto a Versatrack™
Trackwall rail. Do not use the integral hang hook to
mount the tool to any other surface.

WARNING: The Versatrack™ integral hang hook is
not a belt hook.

WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.

WARNING: Before using the tool make sure that the
Versatrack™ integral hang hook is returned to its
original position
IMPORTANT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwallsystem.
1. Turn tool off, remove the battery pack and
removeaccessories.

CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
theVersatrack™ Trackwall.
2. Flip or pull open the integral hang hook
22
. It clicks
when locked into position.
3. Mount the integral hang hook to the
Versatrack™Trackwall.
NOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Fig.W
22
Regular maintenance ensures a long effective life for your
chainsaw.

Craftsman CMCCS620 Specifications

General

Brand	Craftsman
Model	CMCCS620
Category	Chainsaw
Language	English