Prepare for Hardware Hookup
On the wall bracket assembly, remove the connector covers located above and below the
UC-ENGINE to reveal the UC-ENGINE’s connectors.
NOTE: Each connector cover is secured to the wall bracket with a 6-32 Phillips screw. Use a #1
Phillips screwdriver to remove or install the screws. For additional security, replace the screws
with the spanner screws included with the UC-BRKT-100-ASSY. A 1/4 in. driver bit is supplied to
install the spanner screws.
Connect the System
UC-ENGINE
Connect the CCS-UCA-KB-USB, displays, camera, and LAN to the UC-ENGINE. Connections are
made to the top and bottom of the UC-ENGINE.
UC-ENGINE, Bottom (as mounted)
CCS-UCA-KB-USB HD-CONV-USB-200
• CCS-UCA-KB-USB: Connect the USB dongle (supplied with CCS-UCA-KB-USB) to a
port on the USB-ENGINE for local keyboard and mouse control.
• HD-CONV-USB-200: The HD-CONV-USB-200 is already installed on the wall bracket
assembly and connected to the UC-ENGINE.
UC-ENGINE, Top (as mounted)
Camera (not included)
UC-ENGINE
USB speakerphone device
Primary Display
Secondary Display
(Optional)
UC-CONN-HD
• LAN: Connect the CBL-CAT5E-7 cable to the port on the UC-ENGINE and to the
corporate LAN.
NOTE: The UC-ENGINE and PWE-4803RU (connected to the TSW-1060-B-S) must be on
the same network switch.
• Displays:
• Connect the CBL-HD-THIN-HS-6 to the HDMI port on the UC-ENGINE and to the
primary display.
• (Optional) Connect the CBL-USBC-HD-9 to the port on the UC-ENGINE and the
optional secondary display.
• Camera (not included): Connect the camera to the port on the UC-ENGINE with a USB
cable.
• UC-CONN-HD: The UC-CONN-HD is already connected to the UC-ENGINE with the
CBL-MDP-HD-0.5 on the UC-BRKT-100-ASSY.
• USB speakerphone device: Connect any Microsoft Teams or SfB-compliant, AEC enabled
USB speakerphone device such as a Crestron Avia DSP, UC-SB1, UC-SB1-CAM, or third-
party equipment to the port on the UC-ENGINE with a USB cable.
TSW-1060-B-S
TSW-1060-B-S
PWE-4803RU
AC line voltage
TSW-1060-B-S with TSW-1060-TTK-B-S
• Connect the DM-CBL-ULTRA-PC-50 to the LAN PoE port on the TSW-1060-B-S and the
LAN PoE port on the PWE-4803RU.
• Connect a CAT5e cable to the LAN port on the PWE-4803RU and to the corporate LAN.
NOTE: The PWE-4803RU and UC-ENGINE must be on the same network switch.
• Connect the ac power cord on the PWE-4803RU to an ac receptacle.
HD-CONV-USB-200
HD-CONV-USB-200, Top
HDMI Source
The HD-CONV-USB-200 is already installed on the wall bracket assembly and connected to the
UC-ENGINE. Connect an HDMI source to the HDMI port on the HD-CONV-USB-200 with the
included CBL-HD-20 cable.
Complete the Installation
1. Bundle the cables with the integrated cable tie wraps. The cable tie wraps are reusable.
2. Secure the connector covers with the Phillips screws removed earlier or the included
security screws.
3. Connect the power pack cord to a wall outlet.
Apply Power
When all connections are made, press the power button on the bottom of the UC-ENGINE and
apply power to all of the other devices in the system. The touch screen will start and show its IP
address.
Configure the System
Configuring the system consists of two parts; configuring the TSW-1060-B-S, and configuring
the UC-ENGINE.
• Configure the TSW-1060-B-S: Open a web browser to the IP address of the
TSW-1060-B-S (displayed when power was applied) to configure the device to operate in
Teams Video mode. For details, refer to the TSW-560/TSW-760/TSW-1060 Supplemental
Guide (Doc. 927) at www.crestron.com/manuals.
NOTE: The TSW-1060-B-S (via PWE-4803RU) and computer must be on a commonly
accessible network.
• Configure the UC-ENGINE: Configure the system as required. Refer to the UC Video
Conference Systems for Microsoft Teams Supplemental Guide (Doc. 8360) at www.
crestron.com/manuals.
For Additional Information
Scan or click the QR code for detailed product information.
UC-C160-T
For more information, refer to the documents below. All documents can be found at
www.crestron.com/manuals.
• TSW-560/TSW-760/TSW-1060 Supplemental Guide (Doc. 7927)
• HD-CONV-USB-200 Quick Start Guide (Doc. 8354)
• UC Video Conference Systems for Microsoft Teams Supplemental Guide (Doc. 8360)
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions. All other languages are a translation
of the original instructions.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Avia, and DigitalMedia are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered
trademarks of HDMI Licensing LLC in the United States and/or other countries. Huddly IQ is either a trademark or a registered
trademark of Huddly AS in the United States and/or other countries. Skype and Microsoft Teams are either trademarks or
registered trademarks of Microsoft Corporation in the United States and/or other countries. DisplayPort is either a trademark
or registered trademark of the Video Electronics Standards Association (VESA) in the United States and other countries. Other
trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is
not responsible for errors in typography or photography.
©2018 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Doc. 8395B
(2052709)
02.19
Specifications subject to
change without notice.
To Previous Page
Loading...
Need help?
General
