Cub Cadet 1215 User Manual

Figure 29. Air Cleaner Assembly
1 .
Wing Nuts
4.
Paper Cartridge
2.
Cover
5.
Foam Pre-cleaner Element
3.
Hex Nuts
6.
Backplate
SERVICING PAPER CARTRIDGE
This engine is equipped with a dry type air cleaner
element, which should be checked every 100 operating
hours and replaced if dirty. It should be checked and if
necessary replaced more often under extremely dirty,
dusty conditions. Do not wash element in any liquid or
attempt to blow dirt off with air hose as this will punc¬
ture filter element. Carefully handle new element — do
not use if gasket surfaces are bent or twisted. Check
the following when installing a new element: (See Fig¬
ure 29.)
1. Backplate must be flat on gasket of carburetor
elbow. Replace backplate if bent or cracked.
2. Gasket surfaces of element must be flat against
backplate and cover to seal effectively.
3. Seal on cover must be in place to reduce noise
and vibration of the cover. Vibration can cause
stud hole in cover to enlarge, thus permitting dirt
to enter carburetor.
4. Wing nuts must be finger tight — do not
overtighten.
Properly cleaned and installed air cleaner elements
are the best guarantee to continued long and satisfac¬
tory engine life.
CLEANING ENGINE
This tractor has an air-cooled engine. Air must be able
to circulate freely around the engine, through the
screen, shroud, and over the fins of the cylinder head
and cylinder block. Keep these areas free of accumu¬
lated dirt and trash or engine will overheat and result in
damaged moving parts.
SPARK PLUGS
& WARNING
To avoid possible injury, be sure engine is off
and cool before making any adjustment or
repairs.
■ ^NOTE
Remove all dirt from around the spark plugs
before removing.
To remove spark plugs, always use a spark plug
wrench. Check gap after every 100 hours of operation.
Replace a defective plug with a new plug. Set gap at
.030 inch. (See Figure 30.) Tighten plug to 10-15 ft-lbs.
See your authorized dealer for the correct replacement
plug.
Figure 30.
1. Sparkplug
CLEANING OF CYLINDER HEADS
Cleaning of the cylinder heads should only be done by
your authorized Cub Cadet Dealer. This process is to
be done to keep your engine properly cooled and at its
peak efficiency. The frequency of cleaning is depend¬
ent upon the type of fuel used. When leaded fuel is
used the cleaning interval is more frequent than with
unleaded fuel. The cylinder head should also be
cleaned more frequently when the unit is run under a
constant load. The cleaning interval is from 100 to 300
hours.
FIVE SPEED TRANSMISSION (1215 Tractor)
The transmission is lubricated and sealed at the facto¬
ry and does not require checking. If disassembled for
any reason, lubricate with 24 ounces of E.P. Lithium
grease.
HYDROSTATIC TRANS AXLE (1220 Tractor)
Check the oil level four times a year. Lubricant should
be at the point of overflowing. Use SAE E.P. 90 oil.
Drain and refill every two years. The capacity is 2-3/4
pints.
20

Cub Cadet 1215 Specifications

Capacities

fuel tank capacity	3 gals
crankcase capacity	3 pints
transmission capacity	1-1/2 pints
transaxle capacity	2-3/4 pints

Transmission

gears	5 forward speeds and 1 reverse
forward speed	0 to 5.5 mph
reverse speed	0 to 2.35 mph

Engine Specifications

engine make and model	Briggs and Stratton
engine power	12 HP
cylinders	1
bore	3.44 in
stroke	3.06 in
displacement	28.40 cubic inches
low speed	1750 RPM
high idle speed	3400 RPM +-100

Electrical System

system voltage	12 volt neg. ground
alternator	16 amp
fuse	20 amp slow blow
headlights	GE 12 volt 1156

Tires and Dimensions

front tire size	15x6-6
rear tire size	20x10-8
wheelbase	45.0 in
length	68.50 in
turning radius	29.00 in