Cub Cadet 1215 User Manual

HYDROSTATIC OIL LEVEL (1220 Tractor)
A CAUTION
Never use a multi-viscosity oil.
The transmission has been filled at the factory and
should not require changing for the life of the transmis¬
sion. The following oils can be used: Texaco 2209,
General Motors Dextron B, Ford M2C-33F, Mobile
Fluid 300, Cub Cadet hydraulic fluid or a good quality
SAE 20 high detergent oil.
A CAUTION
Overfilling reduces the expansion area in the
reservoir/expansion tank and fluid will spill at
operating temperatures.
The transmission fluid level should be checked prior to
initial use. The level should not be above the “COLD”
mark which is about 1/4 inch from the bottom of the
reservoir/expansion tank. (See Figure 31.)
To check or add fluid to the transmission: (See Fiqure
31.) a
1. R e m o ve the seat and frame cover. Refer to
“FRAME COVER REMOVAL” in the “ADJUST¬
MENT” section.
2. C h e ck the oil level in the reservoir/expansion
tank.
3. if it is necessary to add oil, unscrew the cap on the
reservoir/expansion tank and add oil through the
hole with a funnel. Do not overfill.
4. Reassemble parts.
If frequent additions are required, locate the leak and
correct. Inadequate supply of fluid may result in per¬
manent internal damage.
If contaminant is observed on the reservoir/expansion
tank screen, poor maintenance is indicated. Remove
the reservoir/expansion tank, wash clean, dry and
reinstall. If the screen is pierced, the reservoir/expan¬
sion tank should be replaced.
Hl^ NOTE
The threads on the reservoir/expansion tank
are left hand threaded.
If the natural color of the transmission fluid has
changed to black or milky, overheating and/or water
contamination is indicated. The fluid should be drained
and replaced with new transmission fluid.
To drain the hydrostatic transmission, remove the hex
plug on the bottom of the transmission.
To fill the hydrostatic transmission, remove the vent
plug located next to the reservoir/expansion tank to
prevent an air lock. Replace vent plug. (See Figure 31.)
1. Vent Plug
2. Oil Level Hot
3. Oil Level Cold
HYDROSTATIC TRANSMISSION COOLING
(1220 Tractor)
A CAUTION
Do not use high pressure water spray or steam
to clean the hydrostatic transmission.
The hydrostatic transmission is cooled by the oil, fan
and fins. Normal operating temperature is 180 degrees
F. If the transmission runs hot, check to see if the fan is
in operating condition, the oil level is correct and the
fins are clean.
DRIVE BELT ADJUSTMENT (1220 Tractor)
If a reduction in speed is noticed, the drive belt may
need adjustment. Adjust as follows: (See Figure 32.)
1. Loosen (do not remove) the hex bolt and nut at
the stationary idler bracket.
2. Slide the idler pulley upward to tighten the belt.
Tighten hex nut and bolt.
When no adjustment is left, have belt replaced.
1. Idler Pulley
2. Hex Nut
3. Bolt
4. Drive Belt
21

Cub Cadet 1215 Specifications

Capacities

fuel tank capacity	3 gals
crankcase capacity	3 pints
transmission capacity	1-1/2 pints
transaxle capacity	2-3/4 pints

Transmission

gears	5 forward speeds and 1 reverse
forward speed	0 to 5.5 mph
reverse speed	0 to 2.35 mph

Engine Specifications

engine make and model	Briggs and Stratton
engine power	12 HP
cylinders	1
bore	3.44 in
stroke	3.06 in
displacement	28.40 cubic inches
low speed	1750 RPM
high idle speed	3400 RPM +-100

Electrical System

system voltage	12 volt neg. ground
alternator	16 amp
fuse	20 amp slow blow
headlights	GE 12 volt 1156

Tires and Dimensions

front tire size	15x6-6
rear tire size	20x10-8
wheelbase	45.0 in
length	68.50 in
turning radius	29.00 in