Dell N1548P User Manual

Upgrade Dell EMC Networking N1500 Series Switches
Page 15
## Loading init Ramdisk from multi component Legacy Image at b0000074 ...
Uncompressing Multi-File Image ... OK
boot_prep_linux commandline: console=ttyS0,9600n8 maxcpus=1 mem=1008M root=/dev/ram
mtdparts=spi1.0:1024k(u-
boot);nand_iproc.0:1024k(nboot),512k(nenv),256k(vpd),256k(shmoo),112640k(fs),16384k(diags)
ubi.mtd=fs ethaddr=00:1e:c9:e5:bd:10 quiet
Starting kernel ...
starting pid 1087, tty '': '/etc/init.d/rcS'
starting pid 1217, tty '/dev/ttyS0': '/etc/rc.d/rc.fastpath'
Mounting /dev/mtdblock4 at /mnt/fastpath...done.
Mounting tmpfs at /mnt/application...done.
Dell Networking Boot Options
============================
Select a menu option within 3 seconds or the Operational Code will start automatically...
1 - Start Operational Code
2 - Display Boot Menu
Select (1, 2)#
Extracting Operational Code from .stk file...done.
Loading Operational Code...done.
Decompressing Operational Code...done.
Uncompressing apps.lzma
SyncDB Running...
<185> Aug 21 02:06:22 0.0.0.0-0 General[fp_main_task]: unitmgr.c(6477) 1 %% Reboot 1 (0x1)
DMA pool size: 16777216
AXI unit 0: Dev 0xb150, Rev 0x01, Chip BCM56150_A0, Driver BCM56150_A0
PCI unit 1: Dev 0xb150, Rev 0x01, Chip BCM56150_A0, Driver BCM56150_A0
SOC unit 0 attached to PCI device BCM56150_A0
SOC unit 1 attached to PCI device BCM56150_A0
<186> Aug 21 02:06:43 0.0.0.0-1 General[fp_main_task]: bootos.c(195) 8 %%
Event(0xaaaaaaaa)started!
<185> Aug 21 02:06:43 0.0.0.0-1 SIM[Cnfgr_Thread ]: sim_util.c(3786) 9 %% Switch was reset
due to operator intervention.
(Unit 1 - Waiting to select management unit)>
Applying Global configuration, please wait ...
Applying Interface configuration, please wait ...
console>
5. Verify that the 6.5.2.9 version of firmware is loaded on the switch. The switch or stack is now ready for
normal operation. Verify the configuration and make any changes needed prior to connecting the switch to
the operational network.
console#show version
Machine Description............... Dell EMC Networking Switch
System Model ID................... N1524
Machine Type...................... Dell EMC Networking N1524
Serial Number..................... 14C24M0030LF
Manufacturer...................... 0xbc00
Burned In MAC Address............. 001E.C9E5.BA2F
System Object ID.................. 1.3.6.1.4.1.674.10895.3063
SOC Version....................... BCM56150_A0
HW Version........................ 1
CPLD Version...................... 16
Image File........................ N1500v6.5.2.9
Software Capability............... Stack Limit = 4, VLAN Limit = 512
unit active backup current-active next-active
--- ----------- ----------- -------------- --------------
1 6.5.2.9 6.3.3.14 6.5.2.9 6.5.2.9
End of document

Dell N1548P Specifications

General

Model	N1548P
Switching Capacity	176 Gbps
Forwarding Rate	131 Mpps
PoE Power Budget	740 W
Power Device	Internal power supply
Voltage Required	AC 120/230 V (50/60 Hz)
Operating Temperature	0 °C to 45 °C
Device Type	Switch
Enclosure Type	Rack-mountable
Ports	48 x 10/100/1000
Uplink Ports	4 x 10G SFP+
Routing Protocol	OSPF, RIP, VRRP
Remote Management Protocol	SNMP 1, Telnet, SSH, HTTP, HTTPS
Features	Layer 3 switching, IGMP snooping, Link Aggregation Control Protocol (LACP), Quality of Service (QoS)
Compliant Standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad
Dimensions	4.32 cm
Storage Temperature	70 °C
Relative Humidity	10 to 90% (non-condensing)
Jumbo Frame Support	9216 bytes