EasyManuals Logo
Home>Denon>Receiver>AVR-2312

Denon AVR-2312 Service Manual

Denon AVR-2312
226 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #72 background imageLoading...
Page #72 background image
72
Surround
Surround mode
Surround Parameters
Tone
z16
Audyssey Settings
z18
RESTORER
z21
Height Gain
PLgz Height
z14
AFDM
z15
Surround Back Subwoofer
PRO LOGIC g/gx Music mode only
NEO:6 Music
mode only
Panorama Dimension Center Width Center Image MultEQ
®
XT
Dynamic EQ
®
z19
Dynamic
Volume
®
z20
DIRECT/PURE DIRECT (2 channel)
z1
S
z4
DIRECT/PURE DIRECT (Multi-channel)
z1
STEREO
S S S S S
MULTI CH IN
S
z13
S S S S S S
DOLBY PRO LOGIC gz S S S S S S S
DOLBY PRO LOGIC gx S S S S S S S S S
DOLBY PRO LOGIC g S S S S S S S S S S
DTS NEO:6
S S S S S S S
DOLBY DIGITAL
S
z13
S S S S S S S
DOLBY DIGITAL Plus
S
z13
S S S S S S S
DOLBY TrueHD
S
z13
S S S S S S S
DTS SURROUND
S
z13
S S S S S S S
DTS 96/24
S
z13
S S S S S S S
DTS-HD
S
z13
S S S S S S S
DTS Express
S
z13
S S S S S S
MULTI CH STEREO
S S S S S S S
ROCK ARENA
S S S
z17
S S S S
JAZZ CLUB
S S S S S S S
MONO MOVIE
S S S S S S S
VIDEO GAME
S S S S S S S
MATRIX
S S S S S S S
VIRTUAL
S S S S S
z1 During playback in PURE DIRECT mode, the surround parameters are the same as in DIRECT mode.
z4 Only when “Subwoofer Mode” is set to “LFE+Main”, sound is output from the subwoofer.
z13 This item can be selected when “Surround Parameters” – “PLgz Height” is set to “ON”.
z14 If “Speaker Config.” – “Front Height” is set to “None”, this item cannot be selected.
z15 This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
z16 This item cannot be set when “Dynamic EQ
®
” is set to “ON”.
z17 In this surround mode, bass is +6 dB, and treble is +4 dB. (Default)
z18 For HD Audio whose sampling frequency of an input signal is more than 96 kHz, this sound parameter cannot be set.
z19 This item cannot be set when “MultEQ
®
XT” is set to “OFF” or “Manual”.
z20 This item cannot be set when “Dynamic EQ
®
” is set to “OFF”.
z21 This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.

Table of Contents

Other manuals for Denon AVR-2312

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-2312 and is the answer not in the manual?

Denon AVR-2312 Specifications

General IconGeneral
Impedance8 Ω
Speaker selectorA+B
Input sensitivity200 mV
Pre-out connectivityYes
Audio output channels7.1 channels
Audio A/D Converter (ADC)24-bit/96kHz
Signal-to-Noise Ratio (SNR)100 dB
Total Harmonic Distortion (THD)0.08 %
Power output per channel (1KHz@8 Ohm)135 W
Power output per channel (20-20KHz@8 Ohm)105 W
HDMI in7
Composite video in4
Ethernet LAN (RJ-45) ports1
Multichannel audio input typeRCA
Component video (YPbPr/YCbCr) in2
Headphone connectivity6.3 mm
Connectivity technologyWired
Speakers connectivity typeBinding post
Audio formats supportedAAC, FLAC, MP3, WAV, WMA
Image formats supportedJPG
Wi-FiNo
AM band range522 - 1611 kHz
FM band range87.5 - 108 MHz
Supported radio bandsAM, FM
Preset stations quantity56
Internet radio services supportedLast.fm, Napster
Supported video modes1080i, 1080p, 480i, 480p, 576i, 576p, 720p
DisplayVFD
HDMI version1.4a
Product colorBlack
Audio decodersDolby Pro Logic IIz, Dolby TrueHD, DTS-HD Master Audio
Volume controlRotary
Apple docking compatibilityiPad, iPhone, iPod
Number of products included1 pc(s)
AC input voltage230 V
AC input frequency50 Hz
Power consumption (standby)0.1 W
Power consumption (typical)600 W
Weight and Dimensions IconWeight and Dimensions
Depth382 mm
Width434 mm
Height167 mm
Weight11000 g

Related product manuals