ENGLISH
3
WARNING: To reduce the risk of injury, read the
instructionmanual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
EC-Declaration of Conformity
Machinery Directive
Heavy-Duty Chipping Hammer
D25892
declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-6:2010.
2000/14/EC, Electrical concrete breaker (hand-held), m ≤ 15 kg,
Annex VIII, TÜV Rheinland LGA Products GmbH (0197), D-90431
Nürnberg, Germany, Notified Body ID No.:0197.
Level of sound power according to 2000/14/EC
(Article 12, Annex III, No. 10; m ≤ 15 kg):
L
WA
(measured sound power level) dB(A) 101
L
WA
(guaranteed sound power level) dB(A) 103
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact
at
the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of
.
Markus Rompel
Vice-President Engineering, PTE-Europe
, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
02.11.2017
The vibration and/or noise emission level given in this
information sheet has been measured in accordance with
a standardised test given in EN60745 and may be used to
compare one tool with another. It may be used for a preliminary
assessment ofexposure.
WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However
if the tool is used for different applications, with different
accessories or poorly maintained, the vibration and/or
noise emission may differ. This may significantly increase
the exposure level over the total workingperiod.
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool
is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total workingperiod.
Identify additional safety measures to protect the operator
from the effects of vibration and/or noise such as: maintain
the tool and the accessories, keep the hands warm
(relevant for vibration), organisation of workpatterns.
D25892
Voltage V
AC
230
UK & Ireland V
AC
230/115
Type 1
Frequency Hz 50
Power Input W 1700
No-load beats per minute bpm 1105–2210
Single impact energy (EPTA 05/2009) J 19.4
Max. Impact Joule J 22.7
Tool holder SDS MAX
Weight (including handle) kg 10.0
Noise and vibration total values (triax vector sum) according to EN60745-2-6:
L
PA
(emission sound pressure level)
dB(A) 90
L
WA
(sound power level)
dB(A) 101
K
(uncertainty for the given sound level)
dB(A) 3
Chiselling
Vibration emission value a
h
,
Cheq
= m/s² 13.5*
Uncertainty K = m/s² 1.5
* Measured at the side handle. Side handle vibration is higher than vibration at
the main handle.
English (original instructions)
Congratulations!
You have chosen a
tool. Years of experience, thorough
product development and innovation make
one of the
most reliable partners for professional power toolusers.
Technical Data
HEAVYDUTY CHIPPING HAMMER
D25892
To Next Page
Loading...
Need help?
General
