DeWalt DCF680G2F-QW Original Instructions

10
ENGLISH
Proper Hand Position (Fig. E1–E3)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
DCF680
Proper hand position requires one hand on the main handle as
shown in FigureE1.

WARNING: If the tool will be used in elongate position
and highest MR please hold tool with both hands as
shown in FigureE2.
DCF682
Proper hand position requires two hand on the tool as shown
in FigureE3.
Screwdriving (Fig.A,E)
Your screwdriver uses gyroscopic technology to sense your
hand motion. To operate, press in the motion control activation
trigger and turn your hand in the direction that you want the
screwdriver tooperate.
Setting Initial Starting Point
1. Grasp the screwdriver as shown in FigureE.
2. Press and hold in the motion control activationtrigger.
3. When the LED illuminates the tool is ready foruse.
4. To reset initial starting point first release the motion control
activation trigger. Move tool to new position, then press and
hold in the motion control activationtrigger.
Operating in Forward Direction
1. Grasp the screwdriver as shown in FigureE.
2. Engage head of fastener with screwdriver accessory on work
piece. Follow instructions for setting initial startingpoint.
3. Rotate your hand clockwise and the screwdriver will activate
in the forwarddirection.
Operating in Reverse Direction
1. Grasp the screwdriver as shown in FigureE.
2. Engage head of fastener with screwdriver accessory on work
piece. Follow instructions for setting initial startingpoint.
3. Rotate your hand anti-clockwise and the screwdriver will
activate in the reversedirection.
To turn the tool off, release the motion control activationtrigger.
NOTE: When the tool is not in use or during transit please be
sure to remove any accessory from the tool and activate trigger
lock
2
.
Variable speed
• The spindle speed is dependent upon the speed that you
rotate yourhand.
• The slower you rotate your hand, the slower the
screwdriverturns.
• The faster you rotate your hand, the faster the
screwdriverturns.
• If you wish to increase the spindle speed, rotate your hand
further in the samedirection.
• If you wish to decrease the spindle speed, rotate your hand
back towards the initial startingpoint.
MAINTENANCE
Your
DeWALT
power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
The charger and battery pack are notserviceable.
Lubrication
Your power tool requires no additionallubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by
DeWALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT
recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.

DeWalt DCF680G2F-QW Specifications

General

Brand	DeWalt
Model	DCF680G2F-QW
Category	Power Screwdriver
Language	English