DeWalt XR FLEX VOLT DCS520T2R Manual

ENGLISH
13
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
This heavy-duty plunge saw is a professional power tool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.

WARNING: Use only DeWALT battery packs andchargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. A)
NOTE: Make sure your battery pack
14
is fullycharged.
To Install the Battery Pack into the Tool
1. Align the battery pack
14
with the rails as shown in
FigureA.
2. Slide it in until the battery pack is firmly seated in the tool
and ensure that you hear it snap intoplace.
To Remove the Battery Pack from the Tool
1. Press the release button
15
and firmly pull the battery
packout.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig. A)
Some DeWALT battery packs include a fuel gauge which consists
of three green LED lights that indicate the level of charge
remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge button
20
. A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-userapplication.
Bevel Adjustment (Fig.A)
The bevel angle can be adjusted between 0° and 47°.
1. Loosen the bevel adjustment knobs
7
.
2. Set the bevel angle by tilting the saw shoe
4
until the mark
indicates the desired angle on the bevel scale
6
.
3. Tighten the bevel adjustment knobs
7
.
Changing the Saw Blade (Fig.A–C)
NOTE: It is not necessary to remove the outer blade cover
23
to change the blade.
1. Remove the battery pack.
2. Press the spindle lock button
12
.
3. Press the plunge saw down until it stops (blade
changeposition).
4. Turn the spindle lock lever
13
clockwise until it stops.
5. Hold the spindle lock lever
13
down and using the hex
wrench found in the front handle
11
, rotate the blade until
the lock position is found.
NOTE: The blade
10
is now locked and cannot be turned by
hand.
6. Use the hex wrench to turn the blade clamping screw
24
anti-clockwise to remove.
7. Remove the outer flange
25
and used blade
10
. Place the
new blade on the inner flange
26
.
8. Replace the outer flange
25
and blade clamping screw
24
. Turn the screw clockwise by hand.
NOTE: The direction of rotation of the saw blade and the
rotation of the plunge saw MUST be the same.
9. Tighten the blade clamping screw firmly using the
hexwrench.
10. Release and turn the spindle lock lever
13
anti-clockwise
until it stops.
11. Move the plunge saw back to top position.
12. Push the plunge trigger
1
forward, to take the saw out of
blade change mode.
Adjusting the Riving Knife (Fig.A–C)
For the correct adjustment of the riving knife
21
, refer to
FigureC. Adjust the clearance of the riving knife after changing
the saw blade or whenever necessary.
1. Follow Changing the Saw Blade steps 1–5.
2. Loosen the riving knife adjustment screw
22
with a hex
wrench and set the riving knife as shown in FigureC.
3. Tighten the riving knife adjustment screw
22
.
4. Turn the spindle lock lever
13
anti-clockwise until it stops.
5. Move the plunge saw back to top position.
6. Push the plunge trigger
1
forward, to take the saw out of
blade change mode.
Depth of Cut Adjustment (Fig.D)
The cutting depth can be set at 0–59 mm without guide rail
attached; with the guide rail attached: 0–55 mm.
1. Loosen the depth adjustment knob
8
and move the
pointer to obtain the correct depth of cut.
2. Tighten the depth adjustment knob
8
.
NOTE: For optimal results, allow the saw blade to protrude from
the workpiece by about 3 mm (Fig.D).

DeWalt XR FLEX VOLT DCS520T2R Specifications

General

Brand	DeWalt
Model	XR FLEX VOLT DCS520T2R
Category	Cordless Saw
Language	English