DeWalt XR Li-Ion TOOL CONNECT DCD992 User Manual

12
ENGLISH
Mode Selector (Fig.A,D)
Your tool is equipped with a mode selector that allows
3modes
17
to be customized using the Tool Connect™ app.
Home settings are active when the home indicator
16
is lit.
Refer to Table 1for customizablefeatures.
Once configured, pressing the mode button
14
on the foot of
the tool will cycle through the modes
17
.
If you are unsure of the current configuration, press the mode
selector button
14
to set the tool to the Home setting (home
indicator
16
islit).
DeWALT
Tool Connect™

WARNING: To reduce the risk of injury, remove accessories
from the tool chuck before any Tool Connect™interaction.
NOTICE: Always check the tool configuration prior to use.
If you are unsure of the current configuration, press the
mode selector button
14
(Fig. D) to set the tool to the
Home setting as described on the label and thismanual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://
www.bluetooth.com/Pages/Bluetooth‑Smart‑Devices‑List.aspx)
DeWALT
Tool Connect™ is an application for your smart device
(such as a smart phone or tablet) that connects the device to
your tool to allow you to configure specific tool functions. Refer
to ModeSelector.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by
DeWALT
is under license. Other trademarks and
trade names are those of their respectiveowners.
NOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobileapplication.
Download the
DeWALT
Tool Connect™ applicationat:
• Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from theTool.
• Follow the instructions in the app to create your Tool
Connect™account.
TABLE 1
Customizable Features Home
Factory Presets
Customizable
RangeMode 1 Mode 2 Mode 3
Worklight brightness MED OFF MED HIGH OFF‑HIGH
Worklight delay off 20 secs 20 secs 20 secs 20 minutes 0–20 minutes
Maximum speed (RPM)
in Drill Mode
Speed 1
Speed 2
Speed 3
450
1300
2000
450
1300
2000
450
1300
2000
450
1300
2000
140–450
400–1300
600–2000
Bind‑Up Control®
Disabled Disabled Disabled Disabled
Disabled/
Enabled
• On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to theapp.
• To connect your tool with the
DeWALT
Tool Connect™
app, at the appropriate screen, press the mode selector
button
14
for 3–5 seconds, then wait for the tool to
connect. The tool can only be connected to one Tool
Connect™ account at atime.
Once the tool has been connected, you can confirm that you
would like to register the product.
DeWALT
.comaccount.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
DeWALT
service center. Do not attempt to replace the coin cell
batteryyourself.

WARNING: Danger of explosion if battery is
incorrectlyreplaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2hours and can lead
todeath.
• Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away fromchildren.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medicalattention.
• If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithiumsalts.
• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recyclingfacility.

DeWalt XR Li-Ion TOOL CONNECT DCD992 Specifications

General

Brand	DeWalt
Model	XR Li-Ion TOOL CONNECT DCD992
Category	Drill
Language	English