4. Display Features
4.'t Comfort lcon
The
comfort
icon
is based on
humidity
ranges specified in Figure 7 .
The icon is displayed
for indoor.humidity, remote channel t humidity
and optional remote
channels 2 through 8 humidity.
Figure 7
4.2 Rate of Change
lcon
The rate of change
icon
[4-l
detects rapid
changes
in temperature
and
humidiry lf the arrow
points
upward, the temperature is increasing
at a
rate of
+2"C
per
30
minutes
(or greater),
or
humidity is increasing at
a
rate of
+5%
per
30
minutes
(or greater).
lf the arrow
points
downward,
the temperature is
decreasing
at a
rate
of
-2"C
per
30 minutes
(or
less),
or
humidity is
decreasing at
a rate of
-5%
per
30
minutes
(or
less).
5. Gonsole Operation
,--
Note: The
console has three
buttons
for easy
operation:
MIN/MAX/- button, CLEAR/ADJUST
button, and CHANNEU+ button.
5.1
Min/Max
Mode
The Min/Max mode displays
the minimum and maximum temperature
and humidity
(since
reset of the unit) for the indoor, remote
channel
1
through
8 sensors.
Prior to entering the
MIN/MAX mode,
press
the CHANNEU+ button to
select the temperature
and humidity values
you
wish to view.
1. Display Maximum.
Press the MIN/MAX button once to
display
the maximum.
The MAX icon will
be
displayed.
2.
Clear Maximum. To reset
the maximum
values
to the current
values,
press
and
hold the CLEAR button
for 3
seconds.
3. Display
Minimum. Press
the MIN/MAX
button again to
display the minimum. The MIN icon will be displayed.
4. Clear Minimum.
To reset
the minimum
values to the current
values,
press
and hold the CLEAR button for 3 seconds.
To return to normal mode,
press
the MIN/MAX button again.
5.2
lndoor/Outdoor Channel
Selection
Press the CHANNEU+ button to switch the display between lhe indoor
temperature
and
humidityE, remote
sensors
1 through 8, and scroll
modeQ.. ln scroll mode, all of the indoor and detected outdoor sensors
will be displayed in five second intervals.
5.3 Temperature Units of Measure
The default temperature units of measure are degrees Celsius. To toggle
between degrees Celsius and degrees Fahrenheit,
press
and
hold the
MIN/MAX button for 3 seconds.
5.4 Sensor Search
Mode
lf
any of the sensor communication
is
lost, dashes
G-.-)
will
be
displayed
on the screen. To reacquire the signal:
1. lf
a specific
channel is lost,
press
the CHANNEU+ button to
display thrs channel, then
Press
and hold the CHANNEU+ button
for
3
seconds, and the remote
search
iconq}z will be constantly
displayed for up to 10 minutes. Once the signal is reacquired,
the
remote search icon\7will turn off, and the current values will be
displayed.
2. lf new sensors are added, subtracted, or multiple sensor channels
are lost,
press
the CHANNEU+ button until the indoor channel
isEdisplayed. Press and hold the CHANNEU+ button
for
3
seconds, and the remote search icon
9
will be constantly
displayed for up to 10 minutes. Once the signal is reacquired, the
remote search icon
9
will turn off, and the current values will be
displayed.
5.5 Best Practices for Wireless
Communication
Wireless communication is susceptible to interference, distance, walls
and metal
barriers.
We recommend
the following best
practices
for
trouble free wireless communication.
-9-
1
)
)
\
.,)
RH<45%
RH45%-65% RH>65%
C-)
o
@
Dry
Comfortable
Wet
To Next Page
Loading...
Need help?
General
