To Previous Page

lary applications in accordance with the requirements in the Stand-

ards UL 639 and ULC- S306 for Intrusion Detecti on Units.

For UL/ULC installations use these device onl y in conjunction wi th

compati ble DSC wireless receivers: HSM2HOST9, HS2LCDRF(P)9,

HS2ICNRF(P) 9 and PG9920. After instal lation verify the product func-

tionality in conjunction with the compatible receiver used.

FCC COM PLIAN CE STA TEM ENT

WARNING! Changes or modi fications to this unit not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

This devi ce has been tested and found to comply wi th the limits for

a Class B digi tal device, pursuant to Part 15 of the FCC Rules.

Thes e limits are des igned to provi de reas onabl e protection agai nst

harmful interference in residential installations. This equipment

generates uses and can radiate radio frequency energy and, if not

instal led and used in accordance with the instructions, may cause

harmful interference to radio and televisi on reception.

However, there is no guarantee that interference will not occur in a

particular i nstal lation. If thi s device does caus e such interference,

which can be verified by turning the device off and on, the user is

encouraged to eliminate the interference by one or more of the fol-

lowing measures:

– Re-orient or re-l ocate the receiving antenna.

– Increas e the distance between the device and the recei ver.

– Connect the device to an outlet on a circuit di fferent from the one

that suppl ies power to the receiver.

– Consult the dealer or an experienced radio/TV technician.

FCC ID: F5314PG9944

Industr y C anada St at em ent

This equi pment compli es wi th FCC and IC RF radiation exposure lim-

its set forth for an uncontrol led environment.

This devi ce complies wi th FCC Rules Part 15 and with Indus try

Canada licence-exempt RSS standard( s). Operation is subject to the

following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any i nterference that

may be received or that may cause undesi red operation.

Le present appareil est conforme aux CNR d'Industrie Canada applic-

ables aux appareils radio exempts de licence. L'exploitati on est

autoris ee aux deux condi tions suivantes :(1) l'appareil ne doi t pas

produire de brouil lage, et (2) l'utilisateur de l' appareil doit

accepter tout brouillage radioelectrique subi, meme si le brouil lage

est suscepti ble d'en compromettre le fonctionnement.

IC:160A-PG9944

Europe: The PG4944 and PG8944 are compliant

with the RTTE requi rements - Directive 1999/5/EC of the European

Parli ament and of the Council of 9 March 1999. The PG8944 is cer-

tified to the fol lowing standards: EN50131-2-2 GRADE 2, CLASS IV,

EN50131-6 Type C. Certi fication is for only the 868 MHz variant of

this product. According to EN 50131-1:2006 and A1:2009, this equip-

ment can be appl ied in installed sys tems up to and i ncluding Secur-

ity Grade 2, Environmental Class II. UK: The PG8944 is suitable for

use i n systems installed to conform to PD6662:2010 at Grade 2 and

environmental class 2 BS8243. The Power G peripheral devices have

two-way communication functionali ty, providi ng additi onal benefits

as described in the technical brochure. This functionality has not

been tested to comply with the respective technical requirements

and should therefore be considered outside the scope of the

product’ s certi fication.

Limited Warranty

Digital Security Controls ( DSC) warrants that for a period of twelve

months from the date of purchase, the product shall be free of

defects in materials and workmanshi p under normal use and that in

fulfi lment of any breach of such warranty, DSC shall, at i ts option,

repair or replace the defective equipment upon return of the equi p-

ment to its factory. This warranty applies only to defects in parts

and workmanship and not to damage incurred in shipping or hand-

ling, or damage due to causes beyond the control of DSC such as

lightning, excessive voltage, mechani cal shock, water damage, or

damage arising out of abuse, alteration or i mproper application of

the equipment.

The foregoing warranty shall apply only to the original buyer, and

is and shall be i n lieu of any and all other warranti es, whether

expressed or implied and of all other obligations or liabil ities on

the part of DSC. This warranty contains the entire warranty. Digital

Security Controls neither ass umes responsibility for, nor authorizes

any other person purporti ng to act on its behalf to modify or to

change thi s warranty, nor to as sume for it any other warranty or

liabili ty concerning this product. In no event shall DSC be liable for

any direct or indirect or cons equential damages, los s of antici pated

profits, loss of time or any other los ses incurred by the buyer in

connecti on with the purchas e, installation or operation or fai lure of

this product.

Warning: Digital Security Controls recommends that the enti re s ystem

be completely tested on a regul ar basis. However, despite frequent

testing, and due to, but not limited to, criminal tampering or elec-

trical di sruption, it is possible for this product to fail to perform as

expected.

IMPORTANT - READ CAREFULLY: DSC Software purchas ed wi th or

without Products and Components i s copyrighted and is purchased

under the following license terms:

This End-User License Agreement (“EULA”) is a l egal agreement

between You (the company, individual or enti ty who acquired the

Software and any related Hardware) and Digi tal Security Controls, a

division of Tyco Safety Products Canada Ltd. (“DSC”) , the man-

ufacturer of the integrated security systems and the developer of the

software and any rel ated products or components (“HARDWARE”)

which You acquired. If the DSC software product (“SOFTWARE

PRODUCT” or “SOFTWARE”) is intended to be accompanied by

HARDWARE, and is NOT accompanied by new HARDWARE, You may not

use, copy or i nstal l the SOFTWARE PRODUCT. The SOFTWARE PRODUCT

includes computer software, and may include as sociated media, prin-

ted materials, and “onl ine” or electroni c documentation. Any soft-

ware provided along with the SOFTWARE PRODUCT that is associated

with a separate end-user li cense agreement is licensed to You under

the terms of that li cense agreement.

By i nstal ling, copying, downloadi ng, storing, accessing or otherwise

using the SOFTWARE PRODUCT, You agree uncondi tionally to be

bound by the terms of this EULA, even if thi s EULA is deemed to be

a modificati on of any previous arrangement or contract. If You do not

agree to the terms of this EULA, DSC is unwilling to license the

SOFTWARE PRODUCT to You, and You have no right to use it.

SOFTWARE PRODUCT LI CENSE

The SOFTWARE PRODUCT is protected by copyright laws and inter-

national copyright treati es, as well as other i ntell ectual property

laws and treaties. The SOFTWARE PRODUCT is licensed, not sol d.

1. GRANT OF LICENSE This EULA grants You the foll owing rights:

(a) Software Installation and Use - For each license You acqui re, You

may have onl y one copy of the SOFTWARE PRODUCT instal led.

(b) Storage/Network Use - The SOFTWARE PRODUCT may not be

instal led, accessed, displayed, run, shared or used concurrently on

or from different computers, including a workstation, terminal or

other digital electronic device (“Device”). In other words, if You

have several workstati ons, You will have to acquire a l icense for

each workstation where the SOFTWARE will be used.

PRODUCT, but You may only have one copy per l icense instal led at

any given ti me. You may use the back-up copy solely for archival pur-

poses. Except as expressly provided in this EULA, You may not oth-

erwise make copies of the SOFTWARE PRODUCT, i ncluding the pri nted

materials accompanying the SOFTWARE.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS

(a) Limitations on Reverse Engineering, Decompilation and Disas-

sembly - You may not reverse engineer, decompile, or disassemble

the SOFTWARE PRODUCT, except and only to the extent that such

acti vity is expressly permitted by applicable law notwithstanding

this limitati on. You may not make any changes or modi fications to

the Software, without the written permission of an officer of DSC.

You may not remove any proprietary noti ces, marks or labels from

the Software Product. You shall institute reasonable measures to

ensure compliance with the terms and conditi ons of this EULA.

(b) Separation of Components - The SOFTWARE PRODUCT is licensed

as a single product. Its component parts may not be separated for

use on more than one HARDWARE unit.

HARDWARE, then the SOFTWARE PRODUCT is licensed with the

HARDWARE as a s ingle integrated product. In this case, the

SOFTWARE PRODUCT may onl y be used with the HARDWARE as set

forth in thi s EULA.

(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT.

You may not make it avai lable to others or post it on a server or

web si te.

(e) Software Product Trans fer - You may transfer all of Your rights

under this EULA only as part of a permanent s ale or transfer of the

HARDWARE, provided You retain no copies , You transfer all of the

SOFTWARE PRODUCT (includi ng all component parts , the media and

printed materials , any upgrades and this EULA), and provided the

recipi ent agrees to the terms of this EULA. If the SOFTWARE PRODUCT

is an upgrade, any trans fer must also include all prior versions of

the SOFTWARE PRODUCT.

(f) Termination - Without prejudice to any other rights , DSC may ter-

minate this EULA i f You fail to comply with the terms and conditions

of this EULA. In such event, You must destroy all copies of the

SOFTWARE PRODUCT and all of its component parts.

(g) Trademarks - This EULA does not grant You any rights in con-

nection with any trademarks or service marks of DSC or its sup-

pliers.

3. COPYRIGHT - All titl e and intellectual property rights i n and to the

SOFTWARE PRODUCT (includi ng but not limited to any i mages, pho-

tographs, and text incorporated into the SOFTWARE PRODUCT), the

accompanying printed materials, and any copies of the SOFTWARE

PRODUCT, are owned by DSC or its suppliers. You may not copy the

printed materials accompanying the SOFTWARE PRODUCT. All title and

intell ectual property rights in and to the content which may be

accessed through use of the SOFTWARE PRODUCT are the property of

the respecti ve content owner and may be protected by applicable

grants You no rights to use such content. All rights not expressly

granted under this EULA are reserved by DSC and its suppliers.

4. EXPORT RESTRICTIONS - You agree that You wil l not export or re-

export the SOFTWARE PRODUCT to any country, person, or entity sub-

ject to Canadian export restrictions.

5. CHOICE OF LAW - This Software License Agreement is governed by

the laws of the Province of Ontario, Canada.

6. ARBITRATION - All dis putes arisi ng in connection with this Agree-

ment shall be determined by fi nal and binding arbitration in accord-

ance with the Arbitration Act, and the parties agree to be bound by

the arbi trator’s decision. The pl ace of arbitration shall be Toronto,

Canada, and the l anguage of the arbitration shall be Englis h.

7. LIMI TED WARRANTY

(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT

WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET

YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE

UNINTERRUPTED OR ERROR-FREE.

(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be respons-

ible for problems caused by changes in the operating characteris tics

of the HARDWARE, or for problems in the interaction of the SOFTWARE

PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.

RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR

CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’ S ENTIRE

LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL

BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU

TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS

(CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR

INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE

ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER

WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE

PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER

ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON

ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO

ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS

SOFTWARE PRODUCT.

(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO

CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL,

CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF

WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR

ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT

LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR

ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE

OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME,

PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING

CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that

the entire sys tem be completely tested on a regular basis. However,

despite frequent testing, and due to, but not li mited to, criminal

tampering or electrical disruption, it is possible for this SOFTWARE

PRODUCT to fail to perform as expected.

The term IC before the radio certification number si gnifies that the

Industry Canada technical speci ficati ons were met. Thi s Class B

digital apparatus complies with Canadian ICES-003. This device

complies with RSS-210 of Industry Canada. Operation i s subject to

the following two conditions: ( 1) this device may not caus e inter-

ference, and (2) this devi ce must accept any interference, including

interference that may cause undesired operati on of the device. Cet

appareil numérique de la clas se B est conforme à la norme NMB- 003

du Canada. Ce dispositif sati sfait aux exigences d’Industrie Canada,

prescrites dans le document CNR-210. son util isation est autorisée

seulement aux conditi ons s uivantes: (1) il ne doit pas produire de

brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter

tout brouil lage radi oélectrique reçu, même si ce brouill age est sus-

ceptibl e de compromettre le fonctionnement du dis positif.

Brand	DSC
Model	PG9944
Category	Security Sensors
Language	English

DSC PG9944 User Manual

Questions and Answers:

DSC PG9944 Specifications

Related product manuals