EINHELL GC-CH 18/40 Li User Manual

GB
- 16 -
The battery pack can heat up slightly during char-
ging. This is normal.
If the battery pack fails to charge, please check:
•
whether there is a voltage at the mains power
socket;
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, please send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 4a)
Press the battery capacity indicator switch (item
A). The battery capacity indicator (item B) shows
the charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
Switching ON/OFF.
The hedge trimmer is equipped with a two-han-
ded safety switch. It works only when the switch
on the steady grip (Fig. 6/Item 3a) is pressed with
one hand and the switch (Fig. 3/Item 4a) on the
handle is pressed with the other hand. If either
switch is released, the cutters will stop moving.
Please watch out for the cutters as they slow
down to a standstill.
Notes for use
•
A hedge trimmer can be used to cut shrubs
and bushes as well as hedges.
•
To obtain the best cutting results, hold the
hedge trimmer so that the cutter teeth are
at an angle of approx. 15° in relation to the
hedge (see Fig. 5).
•
The twin-bladed cutters rotate in opposite
directions, thus enabling cutting in both direc-
tions (see Fig. 6).
•
To ensure that you cut the hedge to a level
height, we recommend tying a guide line of
string or similar along the hedge. Cut off all
branches that protrude beyond the guide line
(see Fig. 7).
Warning! Be particularly attentive when cutting
along the guide line. Do not cut through the guide
line. This could get entangled in the blades and
lead to injuries or damage to property.
•
Cut the sides of the hedge with curve-shaped
movements from the bottom up (see Figure
8).
What to do if the blade gets blocked
1. Stop the equipment.
2. Remove the battery.
3. Remove the jammed material from the blade
(wear work gloves to prevent injury when you
do so).
After using
1. Switch off the equipment.
2. Remove the battery.
3. Allow the equipment to cool down and then
store it out of children’s reach.
Anl_GC_CH_18_40_Li_SPK13.indb 16Anl_GC_CH_18_40_Li_SPK13.indb 16 14.10.2021 13:18:0914.10.2021 13:18:09

EINHELL GC-CH 18/40 Li Specifications

General

Blade size	475 mm
Blade type	-
Product color	Black, Red
Cutting length	400 mm
Engine power	- W
Power source	Battery
AC input voltage	18 V

Weight and Dimensions

Weight	2000 g
Package depth	865 mm
Package width	205 mm
Package height	163 mm
Package weight	2800 g