EINHELL GC-PM 40/2 S User Manual

GB
- 18 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the warning signs on the
equipment (see Fig. 14)
1) Read the operating instructions.
2) Take care of the danger from catapulted
parts. Keep a safe distance.
3) Danger! Sharp blades - Switch off the engine
and pull the spark plug boot before doing any
maintenance, repair, cleaning or adjustment
work.
4) Fill with oil and fuel before starting the mower.
5) Caution: Wear ear protection and safety gog
gles.
6) Guaranteed sound power level.
7) Caution! Hot parts. Keep your distance.
8) Fill in fuel only when the engine is switched
off .
9) Starting procedure
10) Engine start/stop lever
(I=Engine on; 0=Engine off )
11) Drive lever (clutch lever)
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
fi re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
2. Layout and items supplied
2.1 Layout (Fig. 1-12)
1a. Engine start/stop lever (engine brake)
1b. Drive lever (clutch lever)
2. Fuel pump (primer)
3. Top and bottom push bar
4a. Debris bag
4b. Level indicator
5a. Ejector fl ap
5b. V-belt
6. Tank fi ller cap
7. Oil fi ller screw
8. Cutting height adjustment
9. Starter cable
10. cable clip
11. Star nut (2x)
12. Long screw (2x)
13. Spark plug wrench
14. 2x screws (bottom push bar)
15. Eyelet
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Anl_GC_PM_40_2_S_SPK7.indb 18Anl_GC_PM_40_2_S_SPK7.indb 18 01.09.2021 14:07:0101.09.2021 14:07:01

EINHELL GC-PM 40/2 S Specifications

General

Type	Push lawn mower
Drive type	Rear wheel drive
Cutting width	400 mm
Product color	Black, Red
Cutting system	Cylinder blades
Number of wheels	4 wheel(s)
Maximum lawn area	1000 m²
Mulching function	-
Fuel tank capacity	0.9 L
Handle(s) features	Ergonomic, Foldable
Engine displacement	132 cm³
Rear wheels diameter	203 mm
Front wheels diameter	178 mm
Recommended oil class	4-stroke lubrication oil
Maximum cutting height	75 mm
Minimum cutting height	25 mm
Grass collecting volume	45 L
Engine number of strokes	4
Number of height positions	7
Cutting clearance adjustment	Yes
Cutting clearance adjustment type	Stepped
Power source	Gasoline

Weight and Dimensions

Weight	21200 g
Package depth	430 mm
Package width	700 mm
Package height	530 mm
Package weight	22500 g