EINHELL VARRITO User Manual

GB
- 18 -
Plug-in tools:
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch
out for foreign bodies in the material and remove
them if necessary.
Plunge cutting is allowed only in soft materials
such as wood or plasterboard.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depen-
ding on choice of abrasive paper for the sanding/
grinding of wood, paint, lacquer, etc.
Notes on working practice:
This equipment off ers particularly high perfor-
mance for the grinding/sanding of hard-to-reach
corners and edges. To grind/sand profi les and
channels you can also work with just the tip or
the edge of the grinding/sanding disk. Various
grinding/sanding papers are available, specially
designed for the diff erent types of material you
may be working on and the amount you wish to
remove from the surface. The amount removed
will depend largely on the choice of sanding/grin-
ding paper and pressure applied to the sanding/
grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice:
Move the plug-in tool against the area you want to
remove. Begin with a fl at angle of incidence and
little pressure. The surface (e.g. wood, plaster)
may be damaged if too much pressure is used.
6.4 Speed control (Fig. 8)
You can select the speed by turning the speed
controller (4).
Plus direction: Higher speed
Minus direction: Lower speed
6.5 Battery capacity indicator (Fig. 9 /Item b)
Press the battery capacity indicator switch (a).
The battery capacity indicator (b) will indicate the
charge status of the battery by means of 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
Always take the battery out of the equipment be-
fore starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Tip! For good results we
recommend high-quality ac-
cessories from !
www.kwb.eu
welcome@kwb.eu
Dust extraction adapter (Art. No.: 44.651.63)
Anl_Varrito_SPK13.indb 18Anl_Varrito_SPK13.indb 18 26.07.2021 08:36:0626.07.2021 08:36:06

EINHELL VARRITO Specifications

General

Soft grip	Yes
Product color	Black, Red
Multi-tool applications	Grinding, Sanding
Power source	Battery
Oscillation angle	3.2 °
Idle oscillation rate (max)	20000 OPM
Idle oscillation rate (min)	11000 OPM
Battery included	No
Sound pressure level (max)	78 dB

Weight and Dimensions

Weight	1000 g