8 www.electrolux.com
Make espresso coee
5 Put one-cup lter cup into lter holder. Add one spoon of ground coee, press it tight with tamper; or
add an E.S.E pod and put it into lter cup. E.S.E (Easy Serving Espresso) Pods can be used to simplify
the espresso preparation. Each pre-packed pod contains 7 grams of coee, already measured and
pressed and sealed between 2 ne layers of lter paper.
6 Fix the lter holder onto brewing head anti-clockwise from “INSERT” to “LOCK” position.
7 Put a warm cup on the drip tray. In “pre-heating done” mode when and and buttons are
steadily and fully light on, press button to start brewing process.
8 Wait a moment and the top-grade coee will ow out. When the machine stops working, your coee is
now ready.
9 Now apply two-cup lter cup. Press button. Brew 2 cups of espresso at the same time.
10 NOTE: If both and buttons start blinking quickly, you may simply press or button to
cancel brewing, or (step 11)
11 (step 10) you may restart brewing after cooling down the boiler. Turning the knob to position
and release hot water from steam nozzle. The pump stops working automatically when it’s done
cooling o. Turn the knob o and resume brewing again.
Make hot water
12 In “pre-heating done” mode when and and buttons are steadily and fully light on, turn the
knob to position. Hot water comes out of the steam nozzle. Turn the knob o when the desired
amount is complete.
Froth milk and make cappuccino/latte
13 Fill a jug with 100ml (for cappuccino) or 200ml (for latte) milk. NOTE: make sure jug diameter is no less
than 70±5mm, and jug capacity can hold twice the milk volume after it’s done frothing.
14 In “pre-heating done” mode when and and buttons are steadily and fully light on, press
button, it starts blinking. NOTE: Use full milk at refrigerator temperature (NOT HOT!).
15 When the button stops blinking, steam / milk frothing function is ready. Before frothing milk, push
steam nozzle in the direction of drip tray, turn the knob to position and release steam until there’s
no water coming out, then turn o steam function by turning the knob back to horizontal ”OFF” position.
16 Immerse steam nozzle in milk about 2cm under the milk surface, turn on the knob. Make sure the steam
nozzle is placed in a position that makes the milk turning in one direction inside the jug from top to
bottom.
17 When the desired level of foam is reached, turn o the knob. NOTE: Clean steam nozzle with wet
sponge immediately after steam stops generating, but care not to hurt! The pump automatically
stops working after milk frothing for 3 minutes.
18 Pour the frothed milk into the espresso prepared, now the cappuccino/latte is ready. Sweeten to taste
and if desired, sprinkle the froth with a little cocoa powder. NOTE: After making steam, you may imme-
diately make espresso again by pressing or button. If both and buttons start blinking
quickly, cool down the boiler and resume brewing (see step 11).
DIY / volume
19 In “pre-heating done” mode when and and buttons are steadily and fully light on, long press
/ button for 3 seconds to start resetting mode. Press / button to start brewing and press
again to stop when the desired volume is complete. Now the volume is saved for next operation and
from then on.
20 Restore factory volume setting simply by long pressing and buttons for 3 seconds again.
CLEANING AND CARE
21 Turn the machine o and unplug the power cord. Let the machine cool down completely before clean-
ing. Wipe all outer surfaces with a damp cloth. Clean water tank, drip tray and drip grid regularly. Never
use caustic or abrasive cleaners, and never immerse the machine in liquid!
To Next Page
Loading...
Need help?
General
