Emerson InSinkErator indulge Series User Manual

Hot & Cool Models Without Filtration
Hot Only Models Without Filtration
D
5
FILL TANK & THEN CONNECT POWER
INSTALLING THE FAUCET
Brass Nut
Run the water for at least 2 minutes to flush
lines (both the hot and cold handles
independently if applicable).
Ferrule
Brass Insert
DO NOT plug in unit until
water flows from faucet
A
B
PREPARATION
Indulge
™
Contemporary, Antique, Tuscan
Invite
™
Contour
™
, Classic
™
Turn screws
until snug.
FILTRATION STANDARD WITH HWT-F1000S
Available as an option. Separate purchase required.
Typical Complete Installation
(Hot & cool model shown)
C
C
C
Brass Nut
Ferrule
Brass Insert
To dispenser
From water
supply
See Installation, Care & Use Manual for important cautions and warnings
IF INSTALLING FILTRATION SYSTEM
Turn off
cold water
supply
Quick & Easy Steps to Instant Hot Water
FINAL WATER CONNECTION
CONNECTING FAUCET TO TANK
Press ALL tubes in once again to ensure secure fit.
Electric Shock Hazard: This appliance MUST be grounded. Using an ungrounded
appliance can result in serious injury or death from electric shock. Improper connection of
the equipment grounding conductor can result in the risk of shock by electricity.
Property Damage: Make sure bends in all water lines are smooth and unkinked, with
no pinching, twisting or blockage. Pinched or blocked water lines may cause damage to
the dispenser tank.
O-Ring
A
A
A
A
A
A
B
B
B
B
B
B
Brass Nut
Ferrule
Hex Tool
(included)
STEP STEP STEP
Models With Filtration
Involve
™
View
®
, Wave
®
(H/HC-View
®
, H/HC-Wave
®
)
Invite Hot100
™
, Hot150
™
blue 1/4" tube
3
2
1
Fiber
Washer
Star Nut
STEP
GN1100, GN2200,
GN2215, HC3300,
H3300
HC1100, HC2200,
HC2215
1-1/4" Small
Steel Washer
1-1/4" Rubber
Washer
white 7/16" tube
clear 5/16"
tube
Hole smaller than 1-1/2”1-1/2” hole
white 1/4" tube
white 1/4" tube
copper 1/4" tube
copper 1/4"
tube
white 1/4"
tube from
connector
Hex Tool
(included)
Indulge
™
Modern
(H/HC3300)
(H-Contour
TM
, H-Classic
TM
)
(H-Hot100, H-Hot150)
(GN/HC1100, GN/HC2200, GN/HC2215)
Flat
Gasket
Trim
Ring
Wing Nut
Rubber Washer
Plastic Spacer
Mounting
Plate
Semi-Circular
Mounting Plate
Long Nut
MOUNTING THE TANK
leave 1/4"
exposed
Hang tank and
tighten screws
with only
1/2 turn
clockwise.
16" or less from
faucet base
and
30" or less
from standard
grounded outlet
DO NOT extend plumbing
or electrical lines
Tank
must be
mounted
level.
STEP
From filter or
water supply line
Plug
From filter or
water supply line
NOTICE
A
B
C
TROUBLESHOOTING
WHAT TO DO
Water and steam
spits forcefully
from spout without
turning on the
dispenser faucet.
Water is not hot.
• Unit is boiling.
May be normal during
initial setup.
• The unit is unplugged.
• The electric outlet is
inoperative.
• Activate faucet lever to release some water from the tank.
• Adjust water temperature using dial on tank front.
Remember that at higher altitudes, water boils at lower
temperatures. See Installation, Care & Use manual.
• Make sure the unit is connected to a properly grounded
electric outlet.
• Make sure the circuit breaker or fuses are functioning properly.
• Check that the outlet is not switched off.
Water is too hot
or not hot enough.
• Thermostat is not adjusted
to your needs.
• Adjust the thermostat slowly, then activate faucet lever for
20 secs. to bring in fresh water at the new setting. Allow 5-7
minutes for water to reach new temperature.
Water comes out the
vent instead of spout.
• Outlet tube is blocked. • Check that outlet tube is not kinked, twisted or pinched.
• Unscrew spout end piece and clean out any debris.
Water is dripping
from the spout/vent
intermittently.
• The expansion chamber
isn’t draining properly due
to low water pressure.
• The spout is blocked.
• Unplug the unit. If the dripping doesn’t stop after a few
minutes, check the supply valve to ensure that it is fully open
and there are no obstructions in the water line reducing the
pressure below 30 psi (i.e., a poorly mounted saddle valve, a
clogged water filter, or a partially opened shut-off valve).
• Unscrew spout end piece and clean out any debris.
Water is dripping
from the spout/vent
constantly.
• Debris in the water line may
be in the faucet valve seat
causing a slow water leak.
• Unscrew spout end piece and clean out any debris.
• Activate faucet lever 7-10 times to flush faucet & lines.
Divided stream.
• Debris in the end piece. • Unscrew spout end piece and clean out any debris.
Water continues to run
after releasing lever.
(Involve
™
View
®
/
Involve
™
Wave
®
)
• Mounting nut too tight.
• Mounting washer not
installed properly.
• Loosen mounting nut, 1/4 turn at a time, until shut-off occurs.
• See Installation, Care & Use manual to check proper mounting
washer installation options.
PROBLEM POSSIBLE CAUSE
FILTRATION ISSUES
(Filtration available as an option)
If you are still experiencing trouble, visit www.insinkerator.com or call the AnswerLine
®
1-800-558-5700.
Water taste or odor.
• Filter needs to be
flushed out.
• Life of filter has expired.
• Activate faucet lever and run until the water is cold.
If no change, replace filter cartridge.
Plea se read Troubleshooting Guide and/or visit
w ww.insinkerator.com before calling AnswerLine
®
New filter leaks or
doesn’t fit.
• Head & bracket not
fully rotated.
• Filter O-ring breach.
• Remove, inspect, reinstall filter cartridge.
• Remove new filter, replace with old filter. Check operation.
If OK, reinstall new filter and recheck operation.
No water flow or
low water flow.
• Life of filter has expired.
• Replace filter cartridge.
Water discoloration/
rusty appearance.
• Corrosion of unit. • Unplug and drain unit as described in the Seasonal Storage/
Drainage section of the Owner’s Manual. If the water
discoloration remains after draining and refilling unit,
discontinue use and contact an authorized InSinkErator
service agent.
To see a tutorial of this installation:
http://goo.gl/AZOHu

Emerson InSinkErator indulge Series Specifications

General

Brand	Emerson
Model	InSinkErator indulge Series
Category	Water Dispenser
Language	English