ghd curve User Manual

USA
operation
Ensure that hair is completely dry before using
the ghd curve appliance.
1 Cool tip
2 Barrel
3 Lever (tong only)
4 Stand
1. Plug your ghd curve into the power supply. The
switch surround will ash white for less than 1
second to indicate that it is now connected to mains
electricity. The appliance is now in standby mode.
2. To heat up the ghd curve for styling, press and hold
the ON/OFF button for at least 2 seconds to turn the
appliance on. Your ghd curve will play a short start
up tune, followed by lights which pulse every 2
seconds to indicate the appliance is heating up.
3. IMPORTANT: ghd curve reaches the required
temperature in seconds, so don’t touch the
hot appliance barrel! Once the ghd curve
appliance has reached operating temperature – the
“at temperature” tune will sound – this is 1 beep.
The ghd curve appliance lights will then
illuminate continuously around the switch to
indicate that the appliance is at temperature and
ready for you to begin styling.
4. When you have nished your styling session,
press and hold the ON/OFF button for more than
2 seconds to turn the appliance o. A shut down
tune will play to indicate the appliance has been
turned o. Once turned o, it is best practice to
unplug the appliance from the mains electricity
and allow it to cool in a safe place. For safe cooling
place the appliance on a ghd heat proof mat
using the built-in safety stand and allow to cool.
WARNING: while the appliance is cooling
down do not touch the barrel or allow children
or those with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge to touch the appliance whilst it
is cooling.
ghd curve has the following safety features:
1. Sleep mode: if your ghd curve has been left
on and has not been used for more than 30
minutes a safety feature will automatically put
the appliance into sleep mode for 10mins, the
appliance will start to cool and the lights around the
button will pulse slowly. After this period of sleep
mode has been exceeded the appliance will then
revert to standby mode. The appliance lights will
turn o at the same time.
a. Note that although ghd curve is turned o, it is
still connected to the mains and should be unplugged
from mains electricity at the earliest opportunity.
b. To restart the appliance while it is in sleep mode,
simply turn it on by pressing and holding down the
ON/OFF button for more than 1 second.
2. Fail safe: in the unlikely event of a control system
error, for safety the heaters will be turned o, ghd
curve will emit rapid beeps and the red lights around
the switch will ash at 1 sec intervals. Switch o the
appliance at the mains and restart. If the unit does not
restart contact ghd Customer Services for advice.
user-maintenance
instructions
Cleaning your ghd curve
1. Unplug the ghd curve from the mains power supply.
2. Always allow the ghd curve to cool before attempting
to clean it.
3. Never immerse the appliance in water.
4. Wipe the outside of the ghd curve with a damp cloth.
Do not use sharp or abrasive detergents or
corrosive products.
Storage
1. Always allow the ghd curve to cool down before
storing away.
2. When the ghd curve has cooled down, fold the power
cord in the same way as it was rst delivered in its
packaging. Do not wrap the supply cord around the
ghd curve as this can strain the cord and cause
premature supply cord failure.
Failure to operate
Your ghd styling appliance is a high performance product
and if the unit is subjected to large uctuation in mains
power during use it may go into fail-safe mode to protect
the unit from damage. Therefore, in the unlikely event that
your ghd product does not operate correctly, check that
the ghd product and mains power supply are switched on,
and that power is available.
If your product stops working and the red fault light
ashes, please follow the procedure below:
1. Switch o the unit
2. Unplug the unit from the plug socket
3. Wait for 5 seconds and then plug the unit back into
the wall
4. Switch the unit back on
If this occurs repeatedly, please contact your local ghd
service centre.
If your product doesn’t switch on, push the yellow test
button followed by the red reset button on the ground
fault plug.
If in doubt, consult a qualied electrician or an approved
ghd retailer, or contact ghd Professional, North America
Inc. at 877-GHD-ANGEL (1-887-443-2643) for
further advice.
adapters
For use in other countries a travel adaptor may be required.
A converter is not needed.
manufacturer’s warranty
All ghd electrical products are individually tested before
leaving the factory. However in the unlikely event of the
product proving defective due to faulty workmanship or
5 ON/OFF Switch
6 Handle
7 Power cord
65
AW1484_US_curve Safety guide STP061014.indd 7-8 06/10/2014 16:31

ghd curve Specifications

General

Brand	ghd
Model	curve
Category	Hair Styler
Language	English