19
Technical Information
Service Manual
Function introduction for combination buttons
Operation guide
Replacement of batteries in remote controller
1. Energy-saving function
1.
After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner.
2. Press "MODE" button to select your required mode:
AUTO, COOL, DRY, FAN, HEAT.
▲
" button to set your required temperature. (Temperature can’t be adjusted under auto mode).
AN" button to set your required fan speed: auto, low, medium and high speed.
5. Press "SWING" button to select fan blowing angle.
● During operation, point the remote control signal sender at the receiving window on indoor unit.
●
The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles between them.
indoor unit during operation.
● Replace new batteries of the same model when replacement is required.
● When you don’t use remote controller for a long time, please take out the batteries
● If the display on remote controller is fuzzy or there’s no display, please replace batteries.
2. 8
3. Child lock function
4. T
emperature display switchover function
About WIFI function(This unit is without WiFi function)
Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to start up or turn off energy-saving function. When energy-saving
function is started up, "SE" will be shown on remote controller, and air conditioner will adjust the set temperature automatically
to factory setting to reach to the best energy-saving effect. Press "TEMP" and "CLOCK"buttons simultaneously again to exit energy-saving
function.
Note:
● Under energy-saving function, fan speed is defaulted at auto speed and it can’t be adjusted.
●
Under energy-saving function, set temperature can’t be adjusted. Press "TURBO"
button and the remote controller won’t send signal.
● Sleep function and energy-saving function can’t operate at the same time. If energy-saving function has been set under cooling mode,
press sleep button will cancel energy-saving function. If sleep function has been set under cooling mode, start up the energy-saving
function will cancel sleep function.
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start
up or turn off 8
ć
heating function. When this function
started up, "
" and "8
ć
"
will be shown on remote controller, and the air conditioner keep the heating status
at 8
ć
. Press "TEMP"
"CLOCK" buttons simultaneously again to exit 8
ć
heating function.
Note:
● Under 8
ć
heating function, fan speed is defaulted at auto speed and it can’t be adjusted.
● Under 8
ć
heating function, set temperature can’t be adjusted. Press
"
TURBO
"
button and the remote controller won’t send signal.
● Sleep function and 8
ć
heating function can’t operate at the same time. If 8
ć
heating function has been set under cooling mode, press
sleep button will cancel 8
ć
heating function. If sleep function has been set under cooling mode, start up the 8
ć
heating function will
cancel sleep function.
● Under
temperature display, the remote controller will display 46
heating.
Press "▲" and "
▲
" simultaneously to turn on or turn off child lock function. When child lock function is on, " " icon is displayed on r
controller. If you operate the remote controller, the " " icon will blink three times without sending signal to the unit.
Under OFF status, press "
▲
" and "MODE" buttons simultaneously to switch temperature display between
ć
and
.
Press "MODE" and "TURBO" button simultaneously to turn on or turn off WIFI function. When WIFI function is turned on, the " WIFI " i
will be displayed on remote controller; Long press "MODE" and "TURBO" buttons simultaneously for 10s, remote controller will send WIFI
reset code and then the WIFI function will be turned on. WIFI function is defaulted ON after energization of the remote controller.
1. Press the back side of remote controller marked with "
out
the cover of battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries, and make sure the position of "+" polar and "-" polar
are correct.
3. Reinstall the cover of battery box.
Note:
signal sender battery
Cover of battery box
remove
reinstall
To Next Page
Loading...
Need help?
General
