Harman Kardon AVR 360 Function Manual

13
ENGLISH
ADVANCED FuNCTIONS
To program, or “record” an activity, follow these steps:
To enter Program mode, simultaneously press and hold the Activity 1.
Button and the Alphanumeric Key or AVR Power On or Off Button to which
the activity will be assigned.
Press the Source Selector (or Setup Button) for each device before you 2.
enter individual commands. This step counts as one of the 19 commands
allowed for each activity.
For Power On, press the AVR or Device Power On Button.3.
Press the AVR or Device Power Off Button for Power Off.4.
Press the Activity Button to end the programming process, and the last 5.
Source Selector (or the Setup Button) will flash three times.
It isn’t possible to “edit” a command within an activity. To erase the activity:
Press and hold the Activity Button and the Alphanumeric Key or AVR 1.
Power On or Off Button until the Source Selector or Setup Button lights.
Press the Activity Button to erase the activity.2.
To execute an activity, press the Activity Button, then press the Alphanumeric
Key (or the AVR Power On or Off Button) for the Activity.
Learning (AVR 460 only)
If you have programmed a product’s codes into the remote and find that some
functions are missing, the AVR 460 remote may “learn” individual codes from
the product’s original remote. See page 24 in the Basic Manual.
Resetting the Remote
To reset the remote to its factory defaults, simultaneously press and hold
the TV Source Selector and the “0” Alphanumeric Key. When the TV Button
relights, enter the code “333”. When the TV Button goes out, and all of the
Source Selectors flash, the remote control will be reset.
PROCESSOR RESET
If the unit behaves erratically after a power surge, first turn off the Main
Power Switch and unplug the AC power cord for at least 3 minutes. Plug the
cord back in and turn the receiver on. If this doesn’t help, reset the AVR.
NOTE : A system reset erases all user configurations, including video
resolution, speaker and level settings, and tuner presets. After a reset,
reenter all of these settings from your notes in the appendix worksheets.
To reset the AVR 460/AVR 360, place it in Standby mode (press the front-
panel Standby/On Switch so that the Power Indicator turns amber). Then
press and hold the front-panel OK Button for at least 5 seconds until the
RESET message appears.
If the receiver does not function correctly ofter a processor reset, contact an
authorized Harman Kardon service center for assistance. Authorized service
centers may be located by visiting the Web site at www.harmankardon.com.
NOTE : After performing a system reset, wait at least 1 minute before
pressing any Source Selectors.
MEMORY
If the AVR 460/AVR 360 is unplugged or experiences a power outage, it will
retain user settings for up to four weeks.

Harman Kardon AVR 360 Specifications

General

Impedance	8 Ω
Receiver type	Surround
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.07 %
Power output per channel (1KHz@6 Ohm)	130 W
Power output per channel (20-20KHz@8 Ohm)	55 W
Headphone outputs	1
Headphone connectivity	-
HDMI in	4
Digital audio optical in	3
Product color	Black, Silver
Audio decoders	Dolby Digital Plus, Dolby Pro Logic IIx, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
Handheld remote control	No
Apple docking compatibility	Not supported
Connectivity technology	Wired
Supported radio bands	AM, FM
Preset stations quantity	30

Weight and Dimensions

Depth	382 mm
Width	440 mm
Height	165 mm
Weight	13400 g