Hayward SharkVAC User Manual

7
Dear Aqua Vac Owner:
Thank you for choosing SharkVAC. In order to achieve optimal performance, please read and follow these steps:
1. Allow the cleaner the first 10 minutes of each use to map pool size and configuration. The normal
programmed cycle is not designed to begin until after this period.
2. Cleaner filter cartridges should be thoroughly cleaned after each use or as often as needed to ensure
cleaner’s optimal performance.
3. Before using your cleaner and especially
when opening the pool for the first time remove larger
items from the pool that may diminish the cleaner’s performance. Clean filter frequently when pool is
excessively dirty.
4. For the first use, run cleaner for the full cycle (2 hours) to ensure a clean pool and give yourself a full
understanding of the cleaner’s capabilities. Subsequent cleanings may take less than a full cycle.
5. Cleaner may periodically go to the wall but not necessarily climb to the vertical position.
This is a normal part of the programmed cycle.
6. Cleaner may stop in the middle of the pool and reverse during cleaning cycle. This is a normal part
of the programmed cycle.
7. DO NOT start cleaner out of the water. Power button should only be switched to "On" position
when unit is submerged. The unit will automatically shut off, but it is best to put power switch in
"OFF" position when unit completes cleaning.
8. Plug in only to GFCI (Ground Fault Circuit Interrupter) protected 12
0VAC volt AC outlet.
9. Place the SharkVAC power supply so that it is at a minimum distance of 11.5 feet from the pool edge.
The length of the standard SharkVAC cable is 50 feet.
READ THESE IMPORTANT OPERATING
TIPS BEFORE USING YOUR UNIT!
STOP
Dear Aqua Vac Owner:
Thank you for choosing SharkVAC. In order to achieve optimal performance, please read and follow these steps:
1. Allow the cleaner the first 10 minutes of each use to map pool size and configuration. The normal
programmed cycle is not designed to begin until after this period.
2. Cleaner filter cartridges should be thoroughly cleaned after each use or as often as needed to ensure
cleaner’s optimal performance.
3. Before using your cleaner and especially
when opening the pool for the first time remove larger
items from the pool that may diminish the cleaner’s performance. Clean filter frequently when pool is
excessively dirty.
4. For the first use, run cleaner for the full cycle (2 hours) to ensure a clean pool and give yourself a full
understanding of the cleaner’s capabilities. Subsequent cleanings may take less than a full cycle.
5. Cleaner may periodically go to the wall but not necessarily climb to the vertical position.
This is a normal part of the programmed cycle.
6. Cleaner may stop in the middle of the pool and reverse during cleaning cycle. This is a normal part
of the programmed cycle.
7. DO NOT start cleaner out of the water. Power button should only be switched to "On" position
when unit is submerged. The unit will automatically shut off, but it is best to put power switch in
"OFF" position when unit completes cleaning.
8. Plug in only to GFCI (Ground Fault Circuit Interrupter) protected 12
0VAC volt AC outlet.
9. Place the SharkVAC power supply so that it is at a minimum distance of 11.5 feet from the pool edge.
The length of the standard SharkVAC cable is 50 feet.
READ THESE IMPORTANT OPERATING
TIPS BEFORE USING YOUR UNIT!
STOP

Hayward SharkVAC Specifications

Power

current consumption	0.78 amps
primary voltage	110-120 volt AC (220-240 volts for 240 volt model)
secondary voltage	24V DC

Motor Specifications

speed	2, 700 rpm
voltage	24V DC, 22V DC, 5V DC
current	2.62 amps, 0.63 amps

Filter

filter type	removable, re-usable, pleated element cartridge
filter porosity	100 micron
filter area	1, 150 sq. inches

Weight and Dimensions

weight without cable	21.5 lbs
cable length	50 ft
shipping weight	21.5 lbs (19.1 kg)