HIKVISION DS-K1T501SF Quick Start Guide

1
2
Video Access Control Terminal
Quick Start Guide
Appearance
Installation
1. Connect the cables with the connector on the rear
panel of the device.
2. Route the cables through the cable hole of the
mounting plate. The cable holes are on the right
side, left side and lower side of the rear cover.
If the right/left side cable hole is selected, remove
the plastic sheet of the cable hole.
3.Secure the mounting plate on
the wall with 4 supplied screws.
4.Connect the corresponding
cables.
5.Push the terminal in the
mounting plate from bottom up.
6.Tighten the screws on the
bottom of the terminal to fix the
terminal on the mounting plate
and complete the installation.
Before You Start:
Make sure that the device in the package is in good condition and all the assembly parts are included.
Make sure that the wall is strong enough to withstand three times the weight of the terminal.
Set the DIP address before installation.
UD06874B-C
©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instrucons on how to use the Product. The soware
embodied in the Product is governed by the user license agreement
covering that Product.
About this Manual
This Manual is subject to domesc and internaonal copyright
protecon. Hangzhou Hikvision Digital Technology Co., Ltd.
(“Hikvision”) reserves all rights to this manual. This manual cannot be
reproduced, changed, translated, or distributed, parally or wholly, by
any means, without the prior wrien permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision
and are registered trademarks or the subject of applicaons for the
same by Hikvision and/or its affiliates. Other trademarks menoned in
this manual are the properes of their respecve owners. No right of
license is given to use such trademarks without express permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF
THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING,
AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN
CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT
IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE
LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS
PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Cable Hole
Plastic Sheet
Cable Hole
Plastic Sheet
DIP Switch
Mic
Camera
LED
Indicator
Fingerprint
Scanner
and
Card Swiping
Area
Voice Talk
Button
Doorbell
Button
Front Left
78mm
218mm
45.5mm
Back
Loud Speaker
Bottom
DIP Switch
Network
Wiegand
TF Card Slot
Door Lock
and RS-485
Micro SIM Card Slot
Serial Port
12V Power
Alarm
The DIP switch from left to right is
from low bit to the high bit.
If the switch is towards ON, it means
the binary value is 1, while OFF
means 0.
For Example, if the DIP switch is as
the picture shown on the left, the
binary value is 0000 1100, which
means the decimal value is 12.
DIP Switch
Network
Wiegand
TF Card Slot
Micro SIM Card Slot
Serial Port
12 V Power
Alarm
Door Lock and RS-485
No. Descripon DIP Switch Status
1 to 4 RS-485 Address
2: Secure Door
Control Unit
0: Card Reader
5
R
S-485 Direcon under
T
erminal Mode
1: Upstream
0: Downstream
6 Work Method
1: Card Reader
0: Terminal
7
W
iegand Protocol
(
Available when Bit 6 is 1)
1: Wiegand 26
0: Wiegand 34
8
M
atched Resistance
(
Available for RS-485
P
rotocol)
1: Enable
0: Disable

HIKVISION DS-K1T501SF Specifications

General

Type	Basic access control reader
Product color	Gray
Cards capacity	50000 cards
Housing material	Metal
Keypad integrated	No
Fingerprint reader	Yes
Authentication type	Access chip/card, Biometric, Face recognition
Transaction capacity	200000
Fingerprint sensor type	Optical
Identification (1:N) time	1.5 s
False Rejection Rate (FRR)	0.01 %
False Acceptance Rate (FAR)	0.001 %
Access chip/card reader type	Contactless
International Protection (IP) code	IP65
DC current (max)	600 A
DC voltage range	12 V
Total megapixels	2 MP
Front camera type	Single camera
PC connected	-
RS-485 ports	1
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	10 - 90 %

Weight and Dimensions

Depth	218 mm
Width	78 mm
Height	41 mm