EasyManuals Logo
Home>HIKVISION>Intercom System>DS-KIS703-P

HIKVISION DS-KIS703-P Manual

HIKVISION DS-KIS703-P
10 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
E N G L I S H
DS-KH6320-WTPE2
Video Intercom Two-Wire Indoor Staon
Diagram References
1 2
3
2
1
3 4 5
6
7
Appearance
Installaon
Before you begin:
Wall Mounng with Juncon Box
Acvate Indoor Staon
1
3
Geng Started
4
Wiring
2
Display Screen
Microphone
Debugging Port
1 2 3
4
5 6 7
1. Make sure the device in the package is in good condion and all the assembly parts
are included.
2. The power supply the indoor staon supports is 12 VDC. Please make sure your
power supply matches your indoor staon.
3. Make sure all the related equipment is power-off during the installaon.
4. Check the product specificaon for the installaon environment.
5. Here takes wall mounitng with juncon box for example.
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate hooks
into the slots on the rear panel of the indoor staon, during which the lock catch will be
locked automacally.
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automacally.
3. Configure the indoor staon and tap Next.
a. Select Indoor Staon Type.
b. Edit Floor and Room No.
4. Linked related devices and tap Next. If the device and the indoor staon are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the door staon in the list to link.
b. Tap the sengs icon to pop up the Network Sengs page.
c. Edit the network parameters of the door staon manually or enable DHCP to get
the network parameters automacally.
d. Oponal: Enable Synchronize Language to synchronize the Language of door
staon with indoor staon.
e. Tap OK to save the sengs.
5. Tap Finish to save the sengs.
The power supply must conform to LPS. The recommended adaptor models and
manufacturers are shown as below. Use the aached adaptor ,and do not change the
adaptor randomly.
1. Power on the device. It will enter the acvaon page automacally.
2. Create a password and confirm it.
3. Tap OK to acvate the indoor staon.
Note: We highly recommend you to create a strong password of your own choosing
(using a minimum of 8 characters, including at least three kinds of following categories:
upper case leers, lower case leers, numbers, and special characters) in order to
increase the security of your product. And we recommend you reset your password
regularly, especially in the high security system, reseng the password monthly or
weekly can beer protect your product.
Loudspeaker
Two-Wire Interface
Alarm Terminal
Power Supply Interface
Note: The debugging port is used for debugging only.
The wall mounng plate and the juncon box are required to install the indoor staon onto
the wall.
The dimension of juncon box should be 75 mm (width) × 75 mm (length) × 50 mm (depth).
The dimension of wall mounng plate is shown.
You are required to acvate the device first by seng a strong password for it before
you can use the device.
1
Quick Configuraon
2
Wall Mounng without Juncon Box
1. Insert 2 expension tubes into the wall.
2. Fix the wall mounng plate to the wall with 2 screws.
3. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the lock
catch will be locked automacally.
122
100
64.85
Unit:mm
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
GND
485-
485+
ALARM IN
RS485
AIN1: Alarm Input 1
AIN2: Alarm Input 2
AIN3: Alarm Input 3
AIN4: Alarm Input 4
AIN5: Alarm Input 5
AIN6: Alarm Input 6
AIN7: Alarm Input 7
AIN8: Alarm Input 8
GND: Grounding
485-: RS-485 Interface
485+: RS-485 Interface
Note: Wiring descripon refers to the User Manual.
Rear Panel (without Interface)
Screw
Wall Mounng Plate
Lock Catch Lock Catch
Lock CatchLock Catch
Juncon Box Wall
Hook
Hook
Hook
Hook
Product Informaon
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instrucons on how to use the Product. The soware embodied in the Product is governed by the
user license agreement covering that Product.
About this Manual
This Manual is subject to domesc and internaonal copyright protecon. Hangzhou Hikvision Digital Technology
Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be reproduced, changed, translated,
or distributed, parally or wholly, by any means, without the prior wrien permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the
subject of applicaons for the same by Hikvision and/or its affiliates. Other trademarks menoned in this manual
are the properes of their respecve owners. No right of license is given to use such trademarks without express
permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN
RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR
OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW.
HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Data Protecon
During the use of device, personal data will be collected, stored and processed. To protect data, the
development of Hikvision devices incorporates privacy by design principles. For example, for device with facial
recognion features, biometrics data is stored in your device with encrypon method; for fingerprint device,
only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable
data protecon laws and regulaons, including without limitaon, conducng security controls to safeguard
personal data, such as, implemenng reasonable administrave and physical security controls, conduct periodic
reviews and assessments of the effecveness of your security controls.
● All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire prevenon regulaons
and other related regulaons in your local region.
● Please use the power adapter, which is provided by normal company. The power consumpon cannot be less than the
required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the device.
● When the product is installed on wall or ceiling, the device shall be firmly fixed.
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please
contact the service center.
● If the product does not work properly, please contact your dealer or the nearest service center. Never aempt to
disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or
maintenance.)
● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the
equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
● Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operang temperature),
cold, dusty or damp locaons, and do not expose it to high electromagnec radiaon.
● The device cover for indoor use shall be kept from rain and moisture.
● Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden
(ignorance can cause fire danger).
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a
malfuncon however), and affecng the endurance of sensor at the same me.
● Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the
acidic sweat of the fingers may erode the surface coang of the device cover.
● Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline
detergents.
● Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you need to return the device
to the factory with the original wrapper. Transportaon without the original wrapper may result in damage on the device
and lead to addional costs.
● Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type
only. Dispose of used baeries according to the instrucons provided by the baery manufacturer.
Safety Instruction
Cauons
Warnings
● Tous les éléments électroniques doivent respecter à la lere la réglementaon locale sur la sécurité des
installaons électriques, sur la prévenon des incendies et des réglementaons connexes en vigueur.
● Ulisez un adaptateur fourni par une entreprise agréée. La consommaon électrique ne doit pas être inférieure à la
valeur exigée.
● Ne branchez pas plusieurs appareils sur un même adaptateur ; toute surcharge de l'adaptateur pouvant entraîner
sa surchauffe ou provoquer un incendie.
● Veillez à bien déconnecter la source d’alimentaon avant de câbler, installer ou démonter l’appareil.
● Lors de l'installaon au mur ou au plafond, assurez-vous que l'appareil est bien fixé.
● Si l'appareil dégage de la fumée ou une odeur suspecte, ou s'il émet des bruits inhabituels, éteignez-le et
débranchez le câble d'alimentaon, puis contactez le SAV.
● Si le produit ne fonconne pas correctement, contactez votre revendeur ou le SAV le plus proche. Vous ne devez en
aucun cas essayer de démonter le produit vous-même. (Nous déclinons toute responsabilité en cas de problèmes
découlant d'une intervenon ou d'une réparaon effectuée sans autorisaon.)
● Évitez de faire tomber l’appareil, de le heurter et de l'exposer à des rayonnements électromagnéques de forte
intensité. Évitez d'installer l'équipement sur des surfaces vibrantes ou à des emplacements subissant des chocs
fréquents (au risque de l'endommager).
● N'installez pas l’appareil à un emplacement trop chaud ou trop froid (reportez-vous à la spécificaon de l’appareil
pour connaître la température de fonconnement précise), poussiéreux ou humide. Ne l'exposez pas non plus à des
rayonnements électromagnéques élevés.
● Le capot de l’appareil pour installaon intérieure ne doit pas être exposé à la pluie, ni à l'humidité.
● Il est formellement interdit d'exposer l'équipement directement au soleil, à un environnement mal venlé ou à une
source de chaleur telle qu'une chaudière ou un radiateur (au risque de provoquer un incendie).
● N'orientez pas l’appareil vers le soleil ou des sources de lumière très vive. Dans le cas contraire, un voile ou des
traînées risquent de se former (ce qui ne constue toutefois pas un dysfonconnement) et la résistance du capteur peut
également être affectée.
● Ulisez le gant fourni pour ouvrir le capot du dôme et évitez tout contact direct avec celui-ci, l'acidité de la sudaon
des doigts pouvant éroder le revêtement du capot de l’appareil.
● Ulisez un chiffon doux et sec pour neoyer les surfaces intérieures et extérieures du capot de l’appareil. N'ulisez
pas de détergents alcalins.
● Conservez tous les emballages ; ils pourront vous resservir ultérieurement. En cas de panne, renvoyez l’appareil à
l'usine dans son emballage d'origine. Si l’appareil est transporté hors de son emballage d'origine, il risque d'être abîmé,
entraînant des frais supplémentaires.
● Une mauvaise ulisaon de la baerie ou un remplacement erroné peut entraîner un risque d'explosion. Ne la
remplacez que par une baerie idenque ou de type équivalent. Meez les baeries usagées au rebut conformément
aux instrucons du fabricant.
Consignes de sécurité
Précauons
Averssements :
Refer to Video Intercom Indoor Staon Configuraon Guide (scan the QR code) for details.
Refer to Video Intercom Indoor Staon Operaon Guide (scan the QR code) for details.
Scan the QR code to get the configuraon
guide for detailed informaon.
Scan the QR code to get the operaon
guide for detailed informaon.
Model Current Manufacturer Standard
MSA-C1500CS24.0-40W-DE 1.5A MOSO POWER SUPPLY TECHNOLOGY CO.,LTD CE
ADS-40FSI-19 24036EPG 1.5A SHENZHEN HONOR ELECTRONIC CO.,LTD CE
Note: Do not wire the cables through the cable
hole (red area) when installing the device with
gang box.

Other manuals for HIKVISION DS-KIS703-P

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HIKVISION DS-KIS703-P and is the answer not in the manual?

HIKVISION DS-KIS703-P Specifications

General IconGeneral
ColorYes
Relay inputs2
Video codecsH.264
Connectivity technologyWired & Wireless
Number of displays supported-
Voice codecsG.711a, G.711u
Megapixel2 MP
Maximum frame rate30 fps
Supported video modes720p, 1080p
Viewing angle, vertical95 °
Maximum video resolution1920 x 1080 pixels
Viewing angle, horizontal144 °
Power consumption (typical)10 W
Operating voltage (door opener)24 V
Operating relative humidity (H-H)10 - 95 %
Door station operating temperature (T-T)-40 - 60 °C
Main monitor station operating temperature (T-T)-10 - 55 °C
Display diagonal7 \
Touchscreen typeCapacitive
Display resolution1024 x 600 pixels
Display technologyTFT
Operating system installedLinux
Product colorSilver
International Protection (IP) codeIP65
Wi-Fi standards802.11b, 802.11g, Wi-Fi 4 (802.11n)
Cabling technology10/100Base-T(X)
Ethernet LAN data rates10, 100 Mbit/s
Ethernet interface typeFast Ethernet
Supported network protocolsTCP/IP, RSTP
Weight and Dimensions IconWeight and Dimensions
Depth140 mm
Width200 mm
Height23.6 mm
Weight334.5 g
Door station dimensions (WxDxH)169 x 110 x 31 mm

Related product manuals