+44(0)333 444 1280 (UK) customer.support@pyronix.com www.pyronix.com Pyronix Limited, Pyronix House, Braithwell Way, Hellaby, Rotherham, S66 8QY, UK
4. Learning procedure
i. Prepare the system for pairing with the device.
- Please refer to control panel instructions.
ii. Remove the piece of polyester lm that is separating the battery from the
battery contacts.
ii. Press and hold the ‘learn button’ on the device for at least 5 seconds and then
release.
- The three LEDs will cycle through on the device whilst the button is held.
iii. On releasing the learn button, the device attempts to pair with the system and
will indicate via the LEDs whether it has been successful or failed.
- The green LED will illuminate to indicate the device has successfully paired
with the system and has adequate signal.
- If the the device fails to pair with the system, the red LED will illuminate.
5. Testing the device
Once learnt to the system, the device will be in a ‘magnet positioning mode’ for 10
minutes, after which the green and red LEDs will extinguish and be disabled. This 10
minute timer can be initiated again by releasing the tamper switch or performing
wireless diagnostics on the device. Whilst in test mode, if the device detects the
magnet, the green LED will illuminate. If the device does not detect the magnet, the
red LED will be illuminated.
After the ‘magnet positioning mode’, the blue LED will light up for 1 hour when the
device is triggered and will extinguish after this period.
6. Using the adhesive strip
If using the adhesive strip to ax the device, the tamper in the main device
and the magnet must be screwed securely if the device is to remain grade 2
compliant.
Programming the device
Once learnt to the system, the zone needs to be programmed so that the
system reacts as intended when the device is triggered.
Please note: Refer to the installation or programming guides provided
with the control panel for advice.
Specications
Please note: To achieve optimum battery life, locate in environments that are
typically room temperature and adhere to installation advice.
Installation advice
Please scan the QR code to the right for installation tips.
Magnet Performance
Learning...
i
Casing & colour
White 2mm polycarbonate-ABS
LED colours
Red, blue and green
Transmission frequency
868MHz FM transceiver narrow band
Transmission method and range
Fully encrypted rolling code, 300m
Tamper switches
Front and rear
Temperature
Storage: -20°C to 50°C
Nominal: -10°C to 50°C
Certied: -10°C to 40°C
Dimensions ( W x H x D) and weight
Device: 29 x 69 x 10mm, 21g
Magnet: 14 x 69 x 10mm, 19g
Battery
1 x lithium CR2450R , 3V,500mAh with a 50mA
pulse
(Ø x H) 24.5 x 5mm
Low voltage threshold 2.2V +/-5%
Battery life up to 2 years
Without Nominal Distance With Nominal Distance (5mm)
Axes of Operation Event Distance in Air Distance on Iron Distance in Air Distance on Iron
Z+
Remove
Approach
53mm
45mm
36mm
26mm
50mm
43mm
30mm
25mm
Z-
Remove
Approach
50mm
40mm
33mm
22mm
47mm
36mm
26mm
24mm
Y
Remove
Approach
40mm
34mm
10mm
8mm
35mm
28mm
9mm
7mm
X+
Remove
Approach
24mm
22mm
22mm
20mm
25mm
23mm
19mm
13mm
X-
Remove
Approach
10mm
9mm
8mm
7mm
12mm
10mm
7mm
4mm
www.pyronix.com/installation-advice/
X+
X-
Z-
Z+
Y
Battery information
When disposing of the product, the battery must be removed and disposed of separately in
accordance with the local regulations.
Product information
For electrical products sold within the European Community. At the end of the electrical products
life, it should not be disposed of with household waste. Please recycle where facilities exist. Check
with your Local Authority or retailer for recycling advice in your country. This product is approved for
use in the Residential, Commercial and Light Industrial Environments.
Warranty & compliance
This product is sold subject to our EXTENDED WIRELESS DEVICES warranty conditions and is
warranted against defects in workmanship for a period of ve years (battery excluded). The 5 year
EXTENDED WIRELESS DEVICES warranty is only applicable when the device has been continually
powered using a Pyronix branded battery, and when returned with the Pyronix branded battery that
has been used in the device. For any products returned without a Pyronix battery, or with
another battery, the standard 2 year warranty applies.
Pyronix batteries are available to purchase from our authorised distributors. For further warranty
information visit: https://www.pyronix.com/terms-conditions-sales/
The declaration of conformity and further compliance documentation may be consulted at:
www.pyronix.com/product-compliance.php
www.pyronix.com/portal
4
5 6
2
iv
>5s
iiiii
To Previous Page
Loading...
Need help?
General
