Deactivating Panic Mode
In the event the user does not want to access a panic button through
the remote control, it can be deactivated from the Code Encryptor 3’s
memory.
1. Unplug the wire harness from the Code Encryptor 3.
2. Press and HOLD the program button.
3. While HOLDING the program button, plug the CE 3 harness back
in. The LED located on the front will turn ON.
4. Wait until the LED turns “OFF”.
5. Once the LED has turned “OFF” release the button. Auto
recognition will start.
TEST THE REMOTES
Press and Release button 1 to Arm “Away”
Press and Release button 2 to “Disarm”
Press and Hold button 1 for 3 seconds to Arm “Stay” or “Bypass”
Press and Hold buttons 1 and 2 for two seconds to activate “Panic”
CE3-002-V0
ARMED
GARAGE
DOOR
OPEN/CLOSE
DISARMED
PROGRAMMED
RELAY
OUTPUT
PANIC
HOLD
BOTH
NOTE: The Code Encryptor 3 will arm in the AWAY mode even if you are outside the house. We do however recommend that you
Arm the alarm system within sight of the status LED or keypad to verify that the system has received and responded to your
remote request.
TROUBLESHOOTING
PROBLEM SOLUTION
Did you program a valid four-digit user code to the Code Encryptor 3?
NOTE: The code you program to the Code Encryptor 3 must be a master code or one of the current
user codes.
I press Button 1 but nothing happens.
Press button 3. If you do NOT hear a “click” at the receiver, see To Add a New Remote in the
Adding/Deleting Remotes section and learn that remote into the Code Encryptor 3.
Did you program the panel for keypad panic? I press and hold buttons 1 and 2 and I do not
get a panic.
Program the Code Encryptor 3 for panic. Turn ON Panic (see Panic Mode section)
I am using a DSC 1832 or any Power Series
and the alarm will not ARM with the remote.
Make sure you program the Alarm panel for “Quick Key Enable,” programming section 015, light #4
is ON. Power down the alarm panel and power it back up. Wait at least 60 seconds before you
attempt to use the remote control.
I am using a DSC Power Series and the alarm
will not DISARM with the remote.
Enter panel programming. Go to programming section 017. Make sure light #1 is on.
I am using a GE Caddx NX panel and it will
only ARM in the STAY mode.
Power down the panel, wait at least 60 seconds and power the panel back up. Reprogram the user
code to the CE3 receiver.
Unit does not seem to identify the panel I am
using.
Call Technical Support at 800-645-7492.
SPECIFICATIONS
Technical Support: M-F 9AM-7PM EST (800) 645-7492; Sales: (858) 513-1224
Receiver: • 12VDC Power Input
• Channels 1 & 2 Data outputs
• Channel 3 Relay (N/O, Common) 10amp -
momentary
• Channel 4 selectable: Form C Relay (N/O,
N/C, Common) 5amp - momentary
• Channel 5 (top 2-buttons at same time) -
Keypad panic data output (Programmable On or OFF)
Frequency: 433 MHz
Stand by Power Consumption: 13mA on standby
(40mA max)
Temperature Range: -5°F to 160°F (Indoor use only)
Remote Control Battery: 6VDC Mini (2x Part #
CR-2025) Replace battery once a year.
WARRANTY INFORMATION
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa
Federal Communications Commission (FCC) Part 15 Statements
The user shall not make any changes or modifications to the equipment unless authorized by the
Installation Instructions or User's Manual. Unauthorized changes or modifications could void the
user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The
FCC requires the following statement for your information: This equipment generates and uses
radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been
type tested and found to comply with the limits for a Class B computing device in accordance with
the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection
against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to
radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on
different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA (IC) STATEMENTS
This device complies with RSS210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries
Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas
causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris
les interferences causant une reception indésirable.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Ê800-04965iŠ
800-04965 8/09 Rev. C
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2009 Honeywell International Inc.
www.honeywell.com/security
To Previous Page
Loading...
Need help?
General
