Husqvarna 701 Supermoto 2023

Questions and Answers

C
Corey NguyenAug 20, 2025
Why does my Husqvarna 701 Supermoto 2023 Motorcycle engine have so little power?
- M
  Mathew WilliamsAug 20, 2025
  If your Husqvarna Motorcycle engine has too little power, start by checking the air filter for dirt and clean or replace it. A dirty fuel screen could also be the cause, so replace it. You should also check the fuel filter and the fuel pressure. Finally, a malfunction in the electronic fuel injection system could be the reason; in this case, read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
G
galvanlindsayAug 22, 2025
Why does my Husqvarna 701 Supermoto 2023 have high oil consumption?
- M
  Melissa CrossAug 22, 2025
  If your Husqvarna Motorcycle has high oil consumption, check the engine vent hose for bends and correct the routing or replace if necessary. Also, verify that the engine oil level is not too high. If the oil is too thin (low viscosity), change the engine oil and the oil filter, and clean the oil screens.
M
Melissa SalasAug 25, 2025
Why doesn't my Husqvarna 701 Supermoto 2023 Motorcycle engine turn over when I press the start button?
- N
  Nicole MillsAug 25, 2025
  If the engine of your Husqvarna Motorcycle doesn't turn when you press the start button, several factors could be at play. It could be due to an operating error, so ensure you're following the correct start procedure. Another potential cause is a discharged 12V battery, which would require charging and an open-circuit current check. Also, check fuses 1, 2, or 3 and the main fuse, replacing them if they're blown. Finally, verify the ground connection is properly established.
A
Amanda BrownAug 26, 2025
What to do if my Husqvarna 701 Supermoto 2023 Motorcycle engine overheats?
- E
  Elizabeth BellAug 26, 2025
  If your Husqvarna Motorcycle engine is overheating, there are several possible causes. First, check the coolant level and look for leaks in the cooling system. Dirty radiator fins can also cause overheating, so clean them. Other potential issues include foam formation or air in the cooling system, which requires draining and bleeding the system. Inspect the radiator hose for buckling or damage, and check the thermostat. A blown fuse 4 or a defect in the radiator fan system could also be the culprit. Address each of these potential causes to resolve the overheating issue.
T
Tyler GutierrezAug 28, 2025
What to do if my Husqvarna 701 Supermoto 2023 engine dies while riding?
- S
  Shelley CooperAug 28, 2025
  If your Husqvarna Motorcycle engine dies during a journey, the first thing to check is the fuel level; refuel if necessary. Also, check fuses 1, 2, and 3, and replace them if they are blown.
K
Katie NguyenAug 30, 2025
Why does my Husqvarna Motorcycle engine turn but not start?
- T
  tturnerAug 30, 2025
  If your Husqvarna Motorcycle engine turns over but doesn't start, first ensure you are following the correct start procedure. Check fuse 3 and replace it if it's blown. Make sure the quick release coupling is joined. If these aren't the issue, there may be a malfunction in the electronic fuel injection, which requires reading the fault memory using the Husqvarna Motorcycles diagnostics tool. Also, avoid opening the throttle while starting and follow the correct start procedure.
S
scottcastroSep 1, 2025
How to fix a discharged 12V battery on my Husqvarna 701 Supermoto 2023 Motorcycle?
- J
  Joe DiazSep 1, 2025
  If the 12V battery on your Husqvarna Motorcycle is discharged, it could be because the ignition was not switched off when the vehicle was parked. In this case, charge the 12V battery. Another reason might be that the alternator is not charging the 12V battery, so check the charging voltage and the open-circuit current.
L
Lisa JacksonSep 3, 2025
Why is the ABS warning lamp on my Husqvarna Motorcycle lit?
- J
  Jacqueline LambertSep 3, 2025
  If the ABS warning lamp lights up on your Husqvarna Motorcycle, it could be due to a blown ABS fuse, so replace the ABS fuses. It may also indicate a large difference in wheel speeds between the front and rear wheels; if this is the case, stop the vehicle, switch off the ignition, and start it again. Finally, it could be a malfunction in the ABS, requiring you to read the ABS fault memory using the Husqvarna Motorcycles diagnostics tool.
A
Austin VasquezSep 4, 2025
Why does my Husqvarna 701 Supermoto 2023 Motorcycle engine only turn when the clutch is pulled?
- L
  Leslie EllisSep 5, 2025
  If your Husqvarna Motorcycle engine only turns when the clutch lever is drawn, it is likely because the vehicle is in gear. Shift the transmission to the neutral position. This can also happen if the vehicle is in gear and the side stand is folded out, so ensure the transmission is in neutral.
A
Angela ShannonSep 7, 2025
What does it mean if the malfunction indicator lamp lights up on my Husqvarna 701 Supermoto 2023?
- H
  holly43Sep 7, 2025
  If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, it indicates a malfunction in the electronic fuel injection system. You should read out the fault memory using the Husqvarna Motorcycles diagnostics tool.

Summary

Safety Advice

Degrees of Risk and Symbols

Explains hazard levels (Danger, Warning, Caution, Note) and associated symbols.

Safety Advice

Reporting Safety Defects

Instructions on how to report vehicle defects that could cause accidents.

Safe Operation

Covers dangers of accidents, poisoning, and burns, plus general safe operation advice.

Protective Clothing

Emphasizes the importance of wearing appropriate protective clothing.

Controls

Emergency OFF Switch

Describes the function of the emergency OFF switch for ignition circuit interruption.

Controls

Combination Switch

Explains the combination switch for riding modes and traction control.

Opening Fuel Tank Filler Cap

Provides instructions and warnings for opening the fuel tank filler cap.

Ignition and Steering Lock

Details the ignition switch positions and steering lock function.

Overview of Indicator Lights

Lists and explains the various indicator lights on the instrument panel.

Side Stand

Locates the side stand and its coupling with the safety starting system.

Combination Instrument

Adjusting the Kilometers or Miles

Setting the Service Display

Speed, Time, and DST2 Distance 2

Setting the Clock

Speed, Time, and DST Distance 1

AVG Average Speed, ART Operating Hours, and ODO Total Distance Covered

Setting the Combination Instrument

Details how to set units (KM/H, M/H) and other settings.

Preparing for Use

Advice on Preparing for First Use

Crucial advice before riding, including safety, controls, and getting acquainted.

Running In the Engine

Guidelines for the engine run-in phase, including speed limits per gear.

Preparing for Use

Loading the Vehicle

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Pre-ride checks list to ensure roadworthiness and proper function.

Starting the Vehicle

Details on starting procedure, safety system, and ABS deactivation.

Braking

More on braking, stopping distance, salt impact, and engine braking.

Refueling

Safety warnings and instructions for refueling the vehicle.

Stopping, Parking

Riding Instructions

Starting Off

Shifting, Riding

Service Schedule

Detailed table of maintenance tasks and intervals (time/mileage).

Tuning the Chassis

Fork;Shock Absorber

Adjusting the Rebound Damping of the Fork

Adjusting the High-Speed Compression Damping of the Shock Absorber

Adjusting the Handlebar Position

Adjusting the Compression Damping of the Fork

Compression Damping of the Shock Absorber

Adjusting the Rebound Damping of the Shock Absorber

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Handlebar Position

Service Work on the Chassis

Installing the Air Filter

Removing the Air Filter

Service Work on the Chassis

Cleaning the Chain

Adjusting the Chain Tension

Procedure for adjusting the drive chain tension correctly.

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Checking chain for wear using weight and measuring chain stretch.

Adjusting the Basic Position of the Clutch Lever

Checking;Correcting the Fluid Level of the Hydraulic Clutch

Checks fluid level, specifies DOT fluid types, and cleaning overflows.

Checking the Chain Tension

How to check the drive chain tension and warnings about incorrect tension.

Brake System

Anti-lock Braking System (ABS)

Explains the ABS system, its components, function, and warnings.

Adjusting the Basic Position of the Hand Brake Lever

Checking the Front Brake Fluid Level

Procedure for checking the front brake fluid level and warnings.

Adding Front Brake Fluid

Top-up procedure for front brake fluid.

Checking that the Brake Linings of the Front Brake are Secured

Checks front brake lining thickness and security.

Adjusting the Basic Position of the Foot Brake Lever

Adding Rear Brake Fluid

Instructions for adding rear brake fluid, including safety warnings.

Checking that the Brake Linings of the Rear Brake are Secured

How to check rear brake lining thickness and security.

Checking the Brake Discs

Guides on checking brake disc thickness, damage, and cracking.

Checking the Free Travel of Foot Brake Lever

Checking the Rear Brake Fluid Level

Procedure for checking the rear brake fluid level and warnings.

Wheels, Tires

Removing the Front Wheel

Detailed steps for safely removing the front wheel.

Removing the Rear Wheel

Steps for safely removing the rear wheel.

Installing the Rear Wheel

Instructions for correctly installing the rear wheel.

Checking the Tire Condition

Checks tire age and recommends replacement after 5 years.

Installing the Front Wheel

Instructions for correctly installing the front wheel.

Checking Tire Pressure

Details recommended tire pressures for solo and passenger use.

Electrical System

Removing the 12-V Battery

Step-by-step guide for safely removing the 12-V battery.

Charging the 12-V Battery

Guidelines and warnings for charging the 12-V battery.

Changing the Main Fuse

Procedure for changing the main fuse and its protective function.

Changing the ABS Fuses

Instructions for changing the fuses related to the ABS system.

Changing the Fuses of Individual Electrical Power Consumers

Details on changing individual fuses for various electrical components.

Installing the 12-V Battery

Instructions for correctly installing the 12-V battery.

Electrical System

Changing the Headlight Bulb

Checking the Headlight Setting

Changing the Turn Signal Bulb

Changing the Parking Light Bulb

Adjusting the Headlight Range

Cooling System

Checking the Antifreeze and Coolant Level

Checks antifreeze concentration and coolant levels in the tank and radiator.

Checking the Coolant Level

Verifies coolant level in compensating tank and radiator.

Draining the Coolant

Cooling System

Filling;Bleeding the Cooling System

Changing the Coolant

Tuning the Engine

Changing the Riding Mode

Checking the Basic Position of the Shift Lever

Adjusting Traction Control

Adjusting the Basic Position of the Shift Lever

Service Work on the Engine

Changing the Fuel Screen

Safety warnings and procedure for changing the fuel screen.

Checking the Engine Oil Level

Procedure for checking the engine oil level at operating temperature.

Adding Engine Oil

Instructions for adding engine oil to the correct level.

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screens

Safety warnings and procedure for changing engine oil and filter.

Cleaning, Care

Cleaning the Motorcycle

Storage

Preparing for Use After Storage

Troubleshooting

The Engine Does Not Turn When the Start Button Is Pressed

Lists possible causes and actions when the engine doesn't crank.

Malfunction Indicator Lamp Lights Up or Flashes

Possible causes and actions when the malfunction indicator lamp is active.

The Engine Turns but Does Not Start

Possible causes and actions when the engine cranks but doesn't start.

Engine Dies During the Journey

Possible causes and actions when the engine stalls during riding.

Engine Has Too Little Power

Possible causes and actions for reduced engine power.

ABS Warning Lamp Lights Up

Possible causes and actions when the ABS warning lamp is illuminated.

Engine Overheats

Possible causes and actions when the engine overheats.

12 V Battery Discharged

Possible causes and actions for a discharged 12V battery.

Technical Data

Engine

Technical specifications for the engine, including design, displacement, bore, stroke, etc.

Technical Data

Engine Tightening Torques

Table of tightening torques for various engine screws and bolts.

Chassis Tightening Torques

Additional chassis tightening torque specifications.

Technical Data

Chassis

Substances

Engine Oil (SAE 10 W;50)

List of Symbols

28.1 Red Symbols

Red symbols indicate error conditions requiring immediate intervention.

28.2 Yellow and Orange Symbols

Yellow/orange symbols indicate errors needing prompt intervention or active driving aids.

Summary

Safety Advice

Degrees of Risk and Symbols

Explains hazard levels (Danger, Warning, Caution, Note) and associated symbols.

Safety Advice

Reporting Safety Defects

Instructions on how to report vehicle defects that could cause accidents.

Safe Operation

Covers dangers of accidents, poisoning, and burns, plus general safe operation advice.

Protective Clothing

Emphasizes the importance of wearing appropriate protective clothing.

Controls

Emergency OFF Switch

Describes the function of the emergency OFF switch for ignition circuit interruption.

Controls

Combination Switch

Explains the combination switch for riding modes and traction control.

Opening Fuel Tank Filler Cap

Provides instructions and warnings for opening the fuel tank filler cap.

Ignition and Steering Lock

Details the ignition switch positions and steering lock function.

Overview of Indicator Lights

Lists and explains the various indicator lights on the instrument panel.

Side Stand

Locates the side stand and its coupling with the safety starting system.

Combination Instrument

Adjusting the Kilometers or Miles

Setting the Service Display

Speed, Time, and DST2 Distance 2

Setting the Clock

Speed, Time, and DST Distance 1

AVG Average Speed, ART Operating Hours, and ODO Total Distance Covered

Setting the Combination Instrument

Details how to set units (KM/H, M/H) and other settings.

Preparing for Use

Advice on Preparing for First Use

Crucial advice before riding, including safety, controls, and getting acquainted.

Running In the Engine

Guidelines for the engine run-in phase, including speed limits per gear.

Preparing for Use

Loading the Vehicle

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Pre-ride checks list to ensure roadworthiness and proper function.

Starting the Vehicle

Details on starting procedure, safety system, and ABS deactivation.

Braking

More on braking, stopping distance, salt impact, and engine braking.

Refueling

Safety warnings and instructions for refueling the vehicle.

Stopping, Parking

Riding Instructions

Starting Off

Shifting, Riding

Service Schedule

Detailed table of maintenance tasks and intervals (time/mileage).

Tuning the Chassis

Fork;Shock Absorber

Adjusting the Rebound Damping of the Fork

Adjusting the High-Speed Compression Damping of the Shock Absorber

Adjusting the Handlebar Position

Adjusting the Compression Damping of the Fork

Compression Damping of the Shock Absorber

Adjusting the Rebound Damping of the Shock Absorber

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Handlebar Position

Service Work on the Chassis

Installing the Air Filter

Removing the Air Filter

Service Work on the Chassis

Cleaning the Chain

Adjusting the Chain Tension

Procedure for adjusting the drive chain tension correctly.

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Checking chain for wear using weight and measuring chain stretch.

Adjusting the Basic Position of the Clutch Lever

Checking;Correcting the Fluid Level of the Hydraulic Clutch

Checks fluid level, specifies DOT fluid types, and cleaning overflows.

Checking the Chain Tension

How to check the drive chain tension and warnings about incorrect tension.

Brake System

Anti-lock Braking System (ABS)

Explains the ABS system, its components, function, and warnings.

Adjusting the Basic Position of the Hand Brake Lever

Checking the Front Brake Fluid Level

Procedure for checking the front brake fluid level and warnings.

Adding Front Brake Fluid

Top-up procedure for front brake fluid.

Checking that the Brake Linings of the Front Brake are Secured

Checks front brake lining thickness and security.

Adjusting the Basic Position of the Foot Brake Lever

Adding Rear Brake Fluid

Instructions for adding rear brake fluid, including safety warnings.

Checking that the Brake Linings of the Rear Brake are Secured

How to check rear brake lining thickness and security.

Checking the Brake Discs

Guides on checking brake disc thickness, damage, and cracking.

Checking the Free Travel of Foot Brake Lever

Checking the Rear Brake Fluid Level

Procedure for checking the rear brake fluid level and warnings.

Wheels, Tires

Removing the Front Wheel

Detailed steps for safely removing the front wheel.

Removing the Rear Wheel

Steps for safely removing the rear wheel.

Installing the Rear Wheel

Instructions for correctly installing the rear wheel.

Checking the Tire Condition

Checks tire age and recommends replacement after 5 years.

Installing the Front Wheel

Instructions for correctly installing the front wheel.

Checking Tire Pressure

Details recommended tire pressures for solo and passenger use.

Electrical System

Removing the 12-V Battery

Step-by-step guide for safely removing the 12-V battery.

Charging the 12-V Battery

Guidelines and warnings for charging the 12-V battery.

Changing the Main Fuse

Procedure for changing the main fuse and its protective function.

Changing the ABS Fuses

Instructions for changing the fuses related to the ABS system.

Changing the Fuses of Individual Electrical Power Consumers

Details on changing individual fuses for various electrical components.

Installing the 12-V Battery

Instructions for correctly installing the 12-V battery.

Electrical System

Changing the Headlight Bulb

Checking the Headlight Setting

Changing the Turn Signal Bulb

Changing the Parking Light Bulb

Adjusting the Headlight Range

Cooling System

Checking the Antifreeze and Coolant Level

Checks antifreeze concentration and coolant levels in the tank and radiator.

Checking the Coolant Level

Verifies coolant level in compensating tank and radiator.

Draining the Coolant

Cooling System

Filling;Bleeding the Cooling System

Changing the Coolant

Tuning the Engine

Changing the Riding Mode

Checking the Basic Position of the Shift Lever

Adjusting Traction Control

Adjusting the Basic Position of the Shift Lever

Service Work on the Engine

Changing the Fuel Screen

Safety warnings and procedure for changing the fuel screen.

Checking the Engine Oil Level

Procedure for checking the engine oil level at operating temperature.

Adding Engine Oil

Instructions for adding engine oil to the correct level.

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screens

Safety warnings and procedure for changing engine oil and filter.

Cleaning, Care

Cleaning the Motorcycle

Storage

Preparing for Use After Storage

Troubleshooting

The Engine Does Not Turn When the Start Button Is Pressed

Lists possible causes and actions when the engine doesn't crank.

Malfunction Indicator Lamp Lights Up or Flashes

Possible causes and actions when the malfunction indicator lamp is active.

The Engine Turns but Does Not Start

Possible causes and actions when the engine cranks but doesn't start.

Engine Dies During the Journey

Possible causes and actions when the engine stalls during riding.

Engine Has Too Little Power

Possible causes and actions for reduced engine power.

ABS Warning Lamp Lights Up

Possible causes and actions when the ABS warning lamp is illuminated.

Engine Overheats

Possible causes and actions when the engine overheats.

12 V Battery Discharged

Possible causes and actions for a discharged 12V battery.

Technical Data

Engine

Technical specifications for the engine, including design, displacement, bore, stroke, etc.

Technical Data

Engine Tightening Torques

Table of tightening torques for various engine screws and bolts.

Chassis Tightening Torques

Additional chassis tightening torque specifications.

Technical Data

Chassis

Substances

Engine Oil (SAE 10 W;50)

List of Symbols

28.1 Red Symbols

Red symbols indicate error conditions requiring immediate intervention.

28.2 Yellow and Orange Symbols

Yellow/orange symbols indicate errors needing prompt intervention or active driving aids.

Husqvarna 701 Supermoto 2023 Specifications

General

Engine Type	Single cylinder, 4-stroke
Displacement	692.7 cc
Bore x Stroke	105 mm x 80 mm
Compression Ratio	12.7:1
Lubrication	Forced oil lubrication with 2 oil pumps
Cooling	Liquid cooled
Transmission	6-speed
Frame	Chromium-Molybdenum steel trellis frame
Seat Height	890 mm
Fuel Tank Capacity	13 liters
Power	55 kW (74 hp) @ 8, 000 rpm
Fuel System	Keihin EFI, 50 mm throttle body
Clutch	APTC(TM) slipper clutch, hydraulically actuated
Final Drive	Chain
Front Suspension	WP APEX 48
Front Brake	Brembo four-piston radial caliper, 320 mm disc
Rear Brake	Brembo single piston caliper, 240 mm disc
ABS	Bosch 9.1 MP
Front Tire	120/70 R17
Rear Tire	160/60 R17
Rear Suspension	WP APEX with Pro-Lever linkage