Husqvarna GT2254 User Manual

47
REPAIR PARTS
TRACTOR - - MODEL NO. GT2254 (96025000200) PRODUCT NO. 960 25 00-02
GEAR DRIVE TRANSAXLE
KEY PART
NO. NO. DESCRIPTION
1 532 12 46-62 Axle Shaft
2 812 00 00-34 Retaining Ring
3 532 00 41-99 Final Drive Gear
4 532 00 42-16 Differential Gear
5 532 00 42-15 Differential Pinion
6 532 00 42-17 Differential Carrier
7 532 17 47-28 Axle Thrust Washer
8 874 02 06-52 Bolt, Hex Head 3/8-24 x 3-1/4
(1” Thread Length)
9 532 12 46-97 Steel Ball
10 532 13 72-61 Spring Shift Fork Detent
11 532 00 49-85 Shift Fork, High-Low Range
12 532 12 49-31 Thrust Bearing Race
13 532 12 46-67 4th Reduction Pinion
14 532 13 71-25 3rd Reduction Gear Shaft
15 532 12 46-77 Snap Ring, Crescent Type
16 532 12 46-79 High-Low Range Gears
17 532 00 81-18 Needle Bearing
18 532 12 47-05 Sintered Iron Bearing
19 532 12 22-38 Shift Fork Shaft, High-Low Range
20 532 00 42-18 Differential Pinion Spacer
21 532 12 46-73 Differential Pinion Bushing
22 532 12 47-01 Gripco Centerlock Nut 3/8-24
23 532 00 62-62 Shift Fork, R.H.
24 532 12 46-98 Oil Seal
25 532 12 47-09 Sintered Iron Bearing
26 532 13 91-11 Shift Fork Shaft
27 532 00 49-86 Shift Fork, L.H.
28 532 12 22-54 Shift Shaft, High-Low Range
29 532 00 62-69 Oil Seal
30 532 00 58-55 Pressure Relief Valve
31 532 17 47-31 Gearcase, Reverse Idler Shaft
and Bearings, R.H. (Includes Key
No.’s 17,18, 25, 33, 50, 63, 77
and 82)
32 532 00 62-77 Dowel Pin
33 532 00 42-25 Needle Bearing
34 532 00 73-96 Thrust Bearing Race
35 532 00 41-98 4th Reduction Gear Shaft
36 532 12 46-63 4th Reduction Gear Spacer
37 532 00 73-95 Thrust Bearing Race
38 532 16 07-89 Gate, Lower, Shift
39 532 17 47-29 Gearcase and Bearings, L.H. (In-
cludes key Numbers 18, 25, 49,
50 (2), 51and 52)
40 813 32 04-00 Pipe Plug 1/2-14 N.P.T.
41 817 58 05-20 Bolt, Hex 5/16-18 UNC x 1-1/4
45 532 00 62-71 Oil Seal
46 813 06 02-00 Pipe Plug 1/4-18 N.P.T.
49 532 12 47-92 Needle Bearlng
50 532 00 42-22 Needle Bearing
51 532 00 15-29 Needle Bearing
KEY PART
NO. NO. DESCRIPTION
52 532 00 81-19 Needle Bearing
53 532 00 42-20 Thrust Bearing Race
54 532 00 42-09 3rd Reduction Pinion, Low
55 532 12 46-68 4th Reduction Gear
56 532 00 44-42 3rd Reduction Pinion Spacer
57 532 00 41-95 2nd Reduction Gear Shaft
58 532 00 42-14 Final Drive Pinion
59 532 00 41-94 1st Reduction Gear Shaft
60 532 00 75-28 1st Reduction Shaft Spacer
61 532 12 46-66 3rd Reduction Plnion Hlgh
62 532 12 46-65 2nd Reduction Gear
63 532 00 73-98 Needle Bearlng
64 532 12 46-64 Low Speed Gear and 2nd Reduc-
tion Pinion Cluster
65 532 00 42-04 Reverse Gear
66 532 00 28-98 Key, Hi-Pro 1/8 x 17/32
67 812 00 00-33 Snap Ring, Crescent Type
68 532 00 42-05 Intermediate Speed Gear
69 532 12 50-99 High Speed Gear
70 532 00 13-70 Thrust Bearing Race
71 532 12 46-81 Intermediate and High Speed
Cluster Pinions
72 532 13 91-20 Input Shaft
73 532 00 42-01 Low Speed Pinion
74 812 00 00-08 E-Ring
75 532 00 11-53 Reverse Idler Gear
77 532 00 68-03 Needle Bearing
79 532 00 11-67 Sealing Washer
80 873 36 07-00 Nut, Hex, Jam 7/16-20
81 532 12 46-75 Oil Seal
82 532 13 69-84 Reverse Idler Shaft
84 532 00 53-84 Gearshift Lever, Bent
85 532 00 29-78 Gearshift Cap
86 532 12 46-82 Gearshift Ball Cover and Pin
87 532 12 47-04 Shift Lever Guide Ball, Keyed
88 532 00 49-24 Spring
89 819 15 15-16 Washer 15/32 x 15/16 x 16
Gauge
90 532 11 05-42 Shift Mechanism Seal
91 819 18 15-11 Washer 9/16 x 15/16 x 12 Gauge
92 532 00 00-75 Gearshift Gate and Reinforce-
ment
93 532 00 62-74 Shift Ball Cover Gasket
94 876 02 04-12 Cotter Pin 1/8 x 3/4
96 532 19 40-36 Bolt, Hex, 5/16-18X1 Epoxy Patch
97 532 19 41-21 Lever Assembly ROS Gear Shift
98 532 18 49-56 Transaxle, 6 Speed,
Complete Assembly
99 532 19 38-33 Actuator, Shift Lever
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

Husqvarna GT2254 Specifications

General

Brand	Husqvarna
Model	GT2254
Category	Lawn Mower
Language	English