Hyundai Atos User Manual

DO-IT-YOURSELF MAINTENANCEDO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCEDO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
6-14
G200A01A-AAT
CHECKING AND REPLACINGCHECKING AND REPLACING
CHECKING AND REPLACINGCHECKING AND REPLACING
CHECKING AND REPLACING
FUSESFUSES
FUSESFUSES
FUSES
Replacing a Fusible LinkReplacing a Fusible Link
Replacing a Fusible LinkReplacing a Fusible Link
Replacing a Fusible Link
A fusible link will melt if the electrical circuits
from the battery are ever overloaded, thus pre-
venting damage to the entire wiring harness.
(This could be caused by a short in the system
drawing too much current.) If this ever happens,
have a Hyundai dealer determine the cause,
repair the system and replace the fusible link.
The fusible links are located in a relay box for
easy inspection.
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION:
When replacing a fusible link, never useWhen replacing a fusible link, never use
When replacing a fusible link, never useWhen replacing a fusible link, never use
When replacing a fusible link, never use
anything but a new fusible link with theanything but a new fusible link with the
anything but a new fusible link with theanything but a new fusible link with the
anything but a new fusible link with the
same or lower amperage rating. Never use asame or lower amperage rating. Never use a
same or lower amperage rating. Never use asame or lower amperage rating. Never use a
same or lower amperage rating. Never use a
piece of wire or a higher-rated fusible link.piece of wire or a higher-rated fusible link.
piece of wire or a higher-rated fusible link.piece of wire or a higher-rated fusible link.
piece of wire or a higher-rated fusible link.
This could result in serious damage andThis could result in serious damage and
This could result in serious damage andThis could result in serious damage and
This could result in serious damage and
create a fire hazard.create a fire hazard.
create a fire hazard.create a fire hazard.
create a fire hazard.
G200A01A
Bad
Good
G180A01A-GAT
CHECKING BRAKE PEDALCHECKING BRAKE PEDAL
CHECKING BRAKE PEDALCHECKING BRAKE PEDAL
CHECKING BRAKE PEDAL
CLEARANCECLEARANCE
CLEARANCECLEARANCE
CLEARANCE
SSA6180A
36 mm (1.42 in.)
You need a helper to check the brake pedal
clearance. With the engine running, have your
helper press down on the brake pedal several
times and then hold it down with a force of about
490N (50kg, 110lbs). The brake pedal clear-
ance is the distance from the top surface of the
brake pedal to the asphalt sheeting under the
floor mat.
If the brake pedal clearance is not within the
limits specified in the illustration, have it in-
spected by your Hyundai dealer and adjusted
or repaired if necessary.
G190A01A-GAT
CHECKING DRIVE BELTSCHECKING DRIVE BELTS
CHECKING DRIVE BELTSCHECKING DRIVE BELTS
CHECKING DRIVE BELTS
Water pump pulley
Crankshaft pulley
Drive belts should be checked periodically for
proper tension and adjusted if necessary. At the
same time, belts should be examined for cracks,
wear, fraying or other evidence of deterioration
and replaced if necessary.
Belt routing should also be checked to be sure
there is no interference between the belts and
other parts of the engine. After a belt is re-
placed, the new belt should be adjusted again
after two or three weeks to eliminate slack
resulting from initial stretching after use.
G190A01A
9.5~11.0 mm
(0.37 ~ 0.43 in.)
Generator

Hyundai Atos Specifications

General

Brand	Hyundai
Model	Atos
Category	Automobile
Language	English