IKEA RENGORA 804.756.07 User Manual

ENGLISH 13
What to do if ...
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the
following list. For other errors or issues please contact authorized After-sales Service which contact details can
be found in the warranty booklet. The manufacturer ensures the availability of spare parts for at least 10 years
after production date of this appliance.
Problems... Possible causes... Solutions...
What to do if ...What to do if ...
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty
booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Salt indicator is lit
Salt reservoir is empty. (After refill
the salt indicator may remain lit
for several wash cycles).
Refill reservoir with sal (for more information - see page 8).
Adjust water hardness - see table, page 8.
Rinse aid indicator is lit
Rinse aid dispenser is empty.
(After refill the rinse aid indicator
may remain lit for several wash
cycles).
Refill dispenser with rinse aid (for more information - see page 8).
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly.
Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. Vigorously push the door until you hear the “click”.
It does not respond to commands.
Display shows: 9 or 12 and
On/Off LED is blinking rapidly.
Switch off the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
If problem persists, unplug the appliance for 1 minute, then plug it
back in.
The dishwasher won’t drain.
Display shows: 3 and
On/Off LED is blinking
rapidly
The wash cycle has not finished yet Wait until the wash cycle finishes
The drain hose is bent. Check that the drain hose is not bent (see INSTALLATION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food
residues.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher makes
excessive noise.
The dishes are rattling against
each.
Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER). Reset the current cycle by switching OFF the
dishwasher, then switch it on again, select a new program, press
START/Pause and close the door within 4 seconds. Please do not
add any detergent.
The dishes are not clean.
The crockery has not been
arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely,
being hindered by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle
and/or detergent efficiency is lo .
Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compart-
ment has not been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does not fill
the water.
Display shows: H
6
and On/Off LED is blin-
king
rapidly
No water in the water supply or
the tap is closed.
Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure the inlet hose is not bent (see INSTALLATION) repro-
gram the dishwasher and reboot.
The sieve in the water inlet hose
is clogged; it is necessary to
clean it.
After having carried out the verification and cleaning, turn o f and
turn on the dishwasher and restart a new program.
Salt indicator is lit
Salt reservoir is empty. (After
rell the salt indicator may
remain lit for several wash
cycles).
Rell reservoir with sal (for more information - see page 8).
Adjust water hardness - see table, page 8.
What to do if ...What to do if ...
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty
booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Salt indicator is lit
Salt reservoir is empty. (After refill
the salt indicator may remain lit
for several wash cycles).
Refill reservoir with sal (for more information - see page 8).
Adjust water hardness - see table, page 8.
Rinse aid indicator is lit
Rinse aid dispenser is empty.
(After refill the rinse aid indicator
may remain lit for several wash
cycles).
Refill dispenser with rinse aid (for more information - see page 8).
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly.
Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. Vigorously push the door until you hear the “click”.
It does not respond to commands.
Display shows: 9 or 12 and
On/Off LED is blinking rapidly.
Switch off the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
If problem persists, unplug the appliance for 1 minute, then plug it
back in.
The dishwasher won’t drain.
Display shows: 3 and
On/Off LED is blinking
rapidly
The wash cycle has not finished yet Wait until the wash cycle finishes
The drain hose is bent. Check that the drain hose is not bent (see INSTALLATION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food
residues.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher makes
excessive noise.
The dishes are rattling against
each.
Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER). Reset the current cycle by switching OFF the
dishwasher, then switch it on again, select a new program, press
START/Pause and close the door within 4 seconds. Please do not
add any detergent.
The dishes are not clean.
The crockery has not been
arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely,
being hindered by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle
and/or detergent efficiency is lo .
Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compart-
ment has not been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does not fill
the water.
Display shows: H
6
and On/Off LED is blin-
king
rapidly
No water in the water supply or
the tap is closed.
Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure the inlet hose is not bent (see INSTALLATION) repro-
gram the dishwasher and reboot.
The sieve in the water inlet hose
is clogged; it is necessary to
clean it.
After having carried out the verification and cleaning, turn o f and
turn on the dishwasher and restart a new program.
Rinse aid indicator is lit
Rinse aid dispenser is empty.
(After rell the rinse aid indicator
may remain lit for several wash
cycles).
Rell dispenser with rinse aid (for more information - see
page 8).
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly.
Insert the plug into the socket.
Power outage. For safety reasons, dishwasher will not re-start automatically
when power returns. Open dishwasher door, press Start
button and close the door within 4 seconds.
The dishwasher door is not
closed.
Natural Dry pin is not pulled in.
Vigorously push the door until you hear the “click”.
It does not respond to
commands. Display shows: 9 or
12 and On/O LED is blinking
rapidly.
Switch o the appliance by pressing the ON/OFF button,
switch it back on after approximately one minute and restart
the program. If problem persists, unplug the appliance for 1
minute, then plug it back in.
The dishwasher won’t drain.
Display shows: 3 and
On/O LED is blinking
rapidly
The wash cycle has not nished
yet
Wait until the wash cycle nishes
The drain hose is bent. Check that the drain hose is not bent (see INSTALLATION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The lter is clogged up with food
residues.
Clean the lter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher makes
excessive noise.
The dishes are rattling against
each.
Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam
has been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER). Restart the current cycle by switching OFF the
dishwasher, then switch it on again, select a new program,
press START/Pause and close the door within 4 seconds.
Please do not add any detergent.
The dishes are not clean.
The crockery has not been
arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate
freely, being hindered by the
dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle
and/or detergent eciency is
low.
Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam
has been produced.
The detergent has not been measured out correctly or it is not
suitable
for use in dishwashers (see FILLING THE DETERGENT
DISPENSER).
The cap on the rinse aid
compartment has not been shut
correctly.
Make sure the cap of the rinse aid dispenser is closed.
The lter is soiled or clogged Clean the lter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

IKEA RENGORA 804.756.07 Specifications

General

Brand	IKEA
Model	RENGORA 804.756.07
Category	Dishwasher
Language	English