EasyManuals Logo
Home>Intellian>Antenna>i6P

Intellian i6P Quick Installation Guide

Intellian i6P
3 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Copyright
®
Intellian Technologies, Inc.
Doc# : i3/i3L/i4/i4P/i5/i5P/i6/i6P/i6PE/i6W DCQ_2015_1103- V1.4
Intellian i3/i3L/i4/i4P/i5/i5P/i6/i6P/i6PE/i6W
Quick Installation Guide
1. Select a location for the antenna.
2. Prepare the mount
3. Prepare the Antenna
4. Secure the Antenna
5. Connect the System Cables
6. Set Region (Nation/City) in ACU
Make sure nearby objects do not block the antenna.
Avoid unnecessary motion by locating the antenna as near
as to the centerline of the boat.
Attach the installation template to the mounting surface using
adhesive tape.
Remove the shaded center portion by using a hole saw.
Drill 4 bolt holes.
Open the antenna upper dome and remove the foam transit
restraints from the antenna base.
Adjust the LNB Skew Angle (Linear Polarization Only).
USA/Japan/Korea is not required to adjust.
Loosen screws of the connection of LNB and feed horn.
Tighten screws after adjusting the LNB position.
Connect the RF Cable from the RF 1
connector on the antenna to the ANT. RF1
connector on the rear of ACU.
Connect the ACU IRD Cable from the
RECEIVER connector on the rear of the ACU
to RF on the IRD.
Connect the power cable from the DC power
connector on the rear of ACU to a power
source of DC (10.8~15.6V).
Note: i3L can only be connected to one receiver.
Turn on the ACU power and you will see USA DTV101 and
DTV 119 as the default.
The system functions will be abnormal if you do not set
a correct continent and region.
Please select your region (Nation/City) after selecting the
continent. Once the SET REGION has been done, you will
not need to adjust GPS and the target tracking satellites.
The setting steps as below.
Enter SETUP MODE and Press NEXT 13 times to enter
LOAD REGION INFO menu.
Select CONTINENT and Press NEXT to select
alternative continents.
Select REGION and Press NEXT to select alternative
Nation/City.
Press YES to load the region setting.
Secure the antenna to the mount base using bolts, spring
washers, and flat washers.
Be sure to put the radome on while operating the
system. The system functions will be abnormal if the
radome is off.
WARNINGWARNING
WARNINGWARNING
Antenna Unit
15°
Obstacle

Other manuals for Intellian i6P

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Intellian i6P and is the answer not in the manual?

Intellian i6P Specifications

Operating Environment IconOperating Environment
operating temperature range-25°C to +55°C
storage temperature range-40°C to +80°C
humidity limit95% R.H
Antenna System Performance IconAntenna System Performance
frequencyKu-band (10.7 to 12.75 GHz)
minimum EIRP46 dBW
azimuth range680°
elevation range-5° to +90°
roll±25°
pitch±15°
roll and pitch response rate45° per second
turn rate45° per second
Power IconPower
power requirements9~30 V DC
power consumption typical30W
power consumption maximum50W
Weight and Dimensions IconWeight and Dimensions
satellite antenna unit dimensions70 cm x 72 cm
antenna dish diameter60 cm
antenna control unit dimensions17.8 cm x 21.7 cm x 5.4 cm
satellite antenna unit weight21 kg
antenna control unit weight1.2 kg

Related product manuals