Intex PureSpa SJB-HS-20-1C Owner's Manual

299
A
S AVE THESE INSTRUCTIONS
(299IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2018
English
Page 15
OPERATION
On/Off Button:
Once the unit is plugged in, use this button to active the control unit panel buttons. The
light next to the button is green when activated. Press this button to turn off all currently activated functions.
NOTE:
The On/Off button may appear as a black button in the center of the control panel.
Heat Button:
Use this button to activate the heating system. The pump will heat the spa water until the
water temperature reaches the set temperature. When the spa water temperature drops 1-2°C (1.8-3.6°F)
  belowthesettemperaturetheheatingsystemwillrestart.Whentheameicononthedisplayisred,the
  heatingsystemisactivated.Whentheameiconturnsgreen,thewaterisatthesettemperature.The
  heatingsystemisatrestandtheltrationsystemwillcontinueworkingnonstop.
NOTE:
Tostoptheltrationsystemwhiletheheaterisatrestmode,presstheamebuttonrstandthen
  thelterbutton.Pressingtheamebuttononlywhiletheheaterisatrestmodewillturnofftheheating
  systemonlyandtheltrationsystemwilloperateforanother24hoursbeforeitturnsoffautomatically.
Celsius/Fahrenheit Toggle button:
The temperature can be displayed in either Fahrenheit or Celsius. The system’s default is Celsius.
CAUTION:
NEVER use the spa if indicated water temperature is more than 40°C (104ºF).
Temperature Adjustment Buttons:
Pressing the Temperature Increase or Decrease buttons will
  causetheLEDtoash.Whenashingyoucanadjusttothedesiredtemperaturesetting.Ifyouholdthese
buttons down the values will rapidly increase or decrease. The new and desired temperature setting will
  remainontheLEDdisplayfor5secondstoconrmthenewvalue.
NOTE:
The default temperature is 20°C (68°F).
NOTE:
Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Water Filter Button:
Thisbuttonturnsthelterpumponandoff.Iftheheatingsystemisactivatedtheltrationsystemwill
automatically start.
  Thewaterltericononthedisplayisgreenwhenactivated.
Water Jet Button:
Use this button to activate the jet massage system. After 30 minutes of continues
use, the jet massage system will automatically turn off. The water jet icon on the displays is green when
activated. The angle of the water jet nozzles inside the spa tub wall can be adjusted manually.
WARNING:
Do not run jet system when the cover is attached, air pressure may accumulate inside the spa
and cause irreparable damage and bodily harm.
Bubble Button:
Use this button to activate the massage system, which has a 30-minute auto-shutoff
feature. The bubble icon on the displays is green when activated.
WARNING:
Do not run Bubble system when the cover is attached, air can accumulate inside the spa and
cause irreparable damage and bodily harm.
Sanitizer Button:
Use this button to activate and set operating hours for the sanitation system.
LED Display:
Once plugged in the LED displays the current water temperature automatically.
NOTE:
Thebuilt-inhardwatertreatmentfunctionworksautomaticallyinconjunctionwiththeltrationsystem.
Jet Nozzle Adjustment
The amount of water and pressure coming out from the jet nozzles can be adjusted by turning the jet
nozzle rim clockwise (maximum water output), counterclockwise (low water output) or anything in between.
Closing one or 2 jet nozzles will divert more water pressure to the other jet nozzles.
A: Heat Button
B: Celsius/Fahrenheit Toggle Button
C: Temperature Increase Button
D: Temperature Decrease Button
E: Water Filter Button
F: Water Jet Button
G: Sanitizer button
H: LED Display
I: On/Off Button
J: Bubble Button
SPA CONTROL UNIT PANEL
40
C
F
J
D
C
B
A
H
G
I
E
40
C
40
C
40
C
40
C
40
C
40
C
40
C
40
C
-
+
-
+
40
C
40
C
o

Intex PureSpa SJB-HS-20-1C Specifications

General

Brand	Intex
Model	PureSpa SJB-HS-20-1C
Category	Swimming Pool
Language	English